Results 161 to 170 of about 628,164 (291)

Compositional data modeling of high-dimensional single cell RNA-seq (CoDA-hd): its advantages over commonly used normalization approaches. [PDF]

J Transl Med
Huang J, Yam SCP, Leung KS, Deng M, Tang NLS.   +4 more
europepmc   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

Sequential Spinodal Decompositions and Ordering Reactions in an As-Quenched Cr₃₉Co₁₈Fe₁₈Ni₁₈Al₇ High-Entropy Alloy. [PDF]

Materials (Basel)
Korir RC, Kenedy GR, Cheng WC, Chen SH.
europepmc   +1 more source

Matrix Algebra and Transformations

, 2021
Lee Stemkoski, Michael Pascale
openaire   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Magnetically Driven Spinodal Decomposition as the Origin of Magnetic Softness of CoFeNi-Based Ferromagnetic High-Entropy Alloys. [PDF]

Chemphyschem
Jelen A, Priputen P, Feuerbacher M, Meden A, Dolinšek J.   +4 more
europepmc   +1 more source

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Protonation-Induced Chemical Transformations in Mass Spectrometry: Implications for Detecting Complex Organics on Icy Moons. [PDF]

ACS Earth Space Chem
Hortal Sánchez L, Napoleoni M, Brunet E, Klenner F, O'Sullivan TR, Ackley M, Danger G, Abel B, Khawaja N, Postberg F.   +9 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

SMILES alignment: a dynamic programming approach for the alignment of metabolites and other small organic molecules. [PDF]

BMC Bioinformatics
Tang AL, Liberles DA.
europepmc   +1 more source