Results 101 to 110 of about 3,750,315 (267)
Advanced Materials, EarlyView.Rapid thiol‐maleimide addition frequently outpaces mixing, resulting in heterogeneous hydrogels. S‐nitrosothiols act as thiol‐protecting groups, allowing uniform mixing with maleimide‐functionalized polymers before gelation. Sodium thiosulfate or sodium ascorbate then regenerates thiols on demand, triggering controlled thiol‐maleimide crosslinking ...
Julian A. Serna +7 more
wiley +1 more source
Applied SciencesAge-related differences in temporomandibular joint osteoarthritis (TMJ OA) have been suggested; however, age-specific patterns of functional recovery following occlusal splint therapy remain insufficiently characterized.
Kun-Hwa Kang +3 more
doaj +1 more source
A lower maximum bite force is a risk factor for developing cardiovascular disease: the Suita study. [PDF]
Sci Rep, 2021 Hashimoto S +10 more
europepmc +1 more source
Dental Microwear Texture Analysis on Radular Teeth
Advanced Materials Interfaces, EarlyView.3D microwear textures reveal how gastropod radular teeth respond to controlled abrasive contact. Distinct surface signatures distinguish regular abrasion from fracture‐dominated material removal, showing how mineralized coatings, fibrous cores, and substrate properties jointly shape wear and failure in a biological scraping interface.
Wencke Krings +2 more
wiley +1 more source
The Journal of Indian Prosthodontic Society, 2017 Introduction: Badly broken or structurally compromised posterior teeth are frequently associated with crown/root fracture. Numerous restorative materials have been used to fabricate indirect full-coverage restorations for such teeth.
Kathleen Manuela D'souza +1 more
doaj +1 more source
Maximum bite force in children with juvenile idiopathic arthritis with and without clinical established temporomandibular joint involvement and in healthy children: a cross-sectional study. [PDF]
J Oral Rehabil, 2021 de Sonnaville WFC +6 more
europepmc +1 more source
Advanced Materials Technologies, EarlyView.Hierarchical multi‐material TPMS lattices are engineered as flexible tactile sensors by combining soft and stiff elastomeric layers with a conformal conductive coating. The bilayer architecture delivers sensitivity at low pressures while maintaining a broad detectable range under large loads, enabling reliable pressure and vibration monitoring for ...
Reza Noroozi +3 more
wiley +1 more source
UCST‐Driven Shape Morphing in Digital Light Processing 4D‐Printed Hydrogels
Advanced Materials Technologies, EarlyView.A DLP‐printable UCST hydrogel based on poly(acrylic acid‐co‐acrylamide) enables reversible thermally induced expansion and 4D shape morphing. Rational control of composition, porosity, and multimaterial architecture enables predictable 4D shape morphing through differential swelling and localized actuation, opening new opportunities for high‐resolution
Fato Niang +2 more
wiley +1 more source
A study of maximum bite force during growth and development.
The Angle orthodontist, 1997 Bilateral bite force was measured in a sample of 457 subjects (231 males and 226 females) from 6 years through 20 years. The mean maximum bite force was found to increase from 78 Newtons at 6 to 8 years to 176 Newtons at 18 to 20 years. While earlier studies have shown adult males have a greater mean bite force than females, this difference is not ...
S, Braun +5 more
openaire +1 more source
Bite-force performance of the last rhynchocephalian (Lepidosauria: Sphenodon)
, 2009 We present the first empirical measurements of bite‐force performance from adult Sphenodon (Rhynchocephalia), the only extant non‐squamate lepidosaur. Using raw bite‐force data, we calculated maximum bite forces at the anterior and posterior extremes of ...
Jones, M., Lappin, K.
core +1 more source