Results 171 to 180 of about 14,324 (259)

Workflow for Design of Experiments‐Based Modeling of Species Transport and Growth Kinetics in GaN Hydride Vapor Phase Epitaxy

Advanced Engineering Materials, EarlyView.
A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič, G. Lukin, H. Torkashvand, A. Kerschbaum, M. Müller, S. Besendörfer, J. Heitmann, J. Friedrich   +7 more
wiley   +1 more source

Mechanical Alloying: An Advantageous Method for the Development of Mg₂Si_0.8Sn_0.2 and Mg₂Si Thermoelectrics Using Commercial and Recyclable Silicon. [PDF]

ACS Appl Energy Mater
Mangelis P, Ioannou PS, So Iland AK, Kyratsi T.   +3 more
europepmc   +1 more source

Kinetics and mechanisms of mechanically alloyed aluminium-carbon alloys

Metal Powder Report, 1995
openaire   +1 more source

Soft Mechanical‐Electrical Logic Using Liquid Metal‐Filled 3D‐Printed Architectures

Advanced Engineering Materials, EarlyView.
We present 3D‐printed soft mechanical–electrical logic elements that use liquid metal–filled silicone tubes actuated by thermoplastic polyurethane/polylactic acid (TPU/PLA) architectures to produce Boolean operations. Complementary normally open and normally closed unit cells perform repeatable binary transitions and can be combined into more complex ...
Christoph Lehmann, Ryan Kalgreen, Laura M. Comella   +2 more
wiley   +1 more source

Structural, Electrical and Corrosion Properties of Bulk Ti-Cu Alloys Produced by Mechanical Alloying and Powder Metallurgy. [PDF]

Materials (Basel)
Arkusz K, Pasik K, Nowak M, Jurczyk M.
europepmc   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

High Milling Time Influence on the Phase Stability and Electrical Properties of Fe₅₀Mn₃₅Sn₁₅ Heusler Alloy Obtained by Mechanical Alloying. [PDF]

Materials (Basel)
Popa F, Marinca TF, Sechel NA, Frunză DI, Chicinaș I.   +4 more
europepmc   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Mechanical Properties and Strengthening Mechanisms of Powder Metallurgy Alloys Produced by Mechanical Alloying

Tetsu-to-Hagane, 1993
Tsunemasa MIURA, Tadashi HASEGAWA
openaire   +2 more sources