Results 201 to 210 of about 2,452,457 (289)

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

Mechanical Alloying: An Advantageous Method for the Development of Mg₂Si_0.8Sn_0.2 and Mg₂Si Thermoelectrics Using Commercial and Recyclable Silicon. [PDF]

ACS Appl Energy Mater
Mangelis P, Ioannou PS, So Iland AK, Kyratsi T.   +3 more
europepmc   +1 more source

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

Materials developed by mechanical alloying and melt spinning

Materials science is a multidisciplinary research topic related to the development of physics and technology. Mechanical alloying of ribbon flakes is a two steps route to develop advanced materials. In this work, a Fe based alloy was obtained using three
Fort, Joaquim, Suñol Martínez, Joan Josep   +1 more
core  

High Milling Time Influence on the Phase Stability and Electrical Properties of Fe₅₀Mn₃₅Sn₁₅ Heusler Alloy Obtained by Mechanical Alloying. [PDF]

Materials (Basel)
Popa F, Marinca TF, Sechel NA, Frunză DI, Chicinaș I.   +4 more
europepmc   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Mechanical Properties and Strengthening Mechanisms of Powder Metallurgy Alloys Produced by Mechanical Alloying

Tetsu-to-Hagane, 1993
Tsunemasa MIURA, Tadashi HASEGAWA
openaire   +2 more sources

Rotary 3D Printing With Integrated Electroplating

Advanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria, Nicola Larovere, Moslem Mohammadi, Gianluca Percoco, Ali Zolfagharian, Gianni Stano   +5 more
wiley   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source