Results 191 to 200 of about 189,256 (267)

Advanced Cellulose-Based Materials: From Nanoparticles to Complex Structures and Composites. [PDF]

Polymers (Basel)
Gorgieva S.
europepmc   +1 more source

Rafting of Ni‐Based Superalloys Under Multiaxial Load as Understood by Phase‐Field Simulations and Critical Experiments

Advanced Engineering Materials, EarlyView.
Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan, David Bürger, Gunther Eggeler, Oleg Shchyglo, Ingo Steinbach, Muhammad Adil Ali   +5 more
wiley   +1 more source

Research on thermo-mechanical coupling behavior of plasma-sprayed mullite ceramic coatings on concrete surfaces. [PDF]

PLoS One
Shi Y, Gong Y, Wang Y, Sun J, Sun H.
europepmc   +1 more source

Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading

Advanced Engineering Materials, EarlyView.
The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley   +1 more source

Effect of Build-Up Strategy and Selective Laser Melting Process Parameters on Microstructure and Mechanical Properties of 316L Stainless Steel. [PDF]

Materials (Basel)
Żaba K, Balcerzak M, Pałka P, Čada R, Trzepieciński T, Szczepańska M.   +5 more
europepmc   +1 more source

Affecting the Properties of Copper–Graphene Electroconductive Composite by Severe Plastic Deformation

Advanced Engineering Materials, EarlyView.
Copper‐based composites enhanced with carbon feature convenient mechanical properties and favorable electric conductivity. Processing via deformation and thermomechanical treatments can introduce advantageous microstructures further enhancing their performance. Herein, copper–graphene powder‐based composites are directly consolidated via rotary swaging
Radim Kocich, Lenka Kunčická, Pavel Czernek, Zifan Wang   +3 more
wiley   +1 more source

Design of fault water-resisting coal pillars based on deep-beam analysis: A comparison of two analytical methods. [PDF]

PLoS One
Wang B, Zha W, Lu H.
europepmc   +1 more source

Microstructure Evolution of a VMnFeCoNi High‐Entropy Alloy After Synthesis, Swaging, and Annealing

Advanced Engineering Materials, EarlyView.
The synthesis and processing (rotary swaging and annealing) of the novel VMnFeCoNi alloy is investigated, alongside the estimation of the grain size effect on hardness. Analysis of a wide grain size range of recrystallized microstructures (12–210 µm) reveals a low annealing twin density.
Aditya Srinivasan Tirunilai, Zeki Ayrildi, Buse Şen, Maik Rajkowski, Mathias Redondo Garcia, Markus Stricker, Guillaume Laplanche   +6 more
wiley   +1 more source

An Intelligent Floor Drain System for Self-Powered Disinfection via Low-Velocity Wastewater Energy Harvesting. [PDF]

Research (Wash D C)
Huang Z, Wang Y, Wang Y, Bowen CR, Yoon HJ, Yang Y.   +5 more
europepmc   +1 more source

A Topology Optimization Framework for the Inverse Design of Nonlinear Mechanical Metamaterials

Advanced Engineering Materials, EarlyView.
This work uses topology optimization to design unit cells for mechanical metamaterials with a prescribed nonlinear stress–strain response. The framework adds contact and postbuckling modeling to synthesize microstructures for three highly nonlinear responses, including pseudoductile behavior, monostable with snap‐through buckling, and bistable ...
Charlie Aveline, Matthew Santer, Robert Hewson   +2 more
wiley   +1 more source