Results 231 to 240 of about 344,022 (350)

Dynamic Compression Mechanical Behavior of Three-Dimensional Chiral Mechanical Metamaterials: Effects of Geometric Parameters and Size. [PDF]

Materials (Basel)
Qin S, Huang Z, Cao W, Cao X, Lin Y.
europepmc   +1 more source

Powder Metallurgy Preparation of Metastable β Ti–Cr–Ge Alloys for Medical Applications

Advanced Engineering Materials, EarlyView.
This study develops metastable β Ti–Cr–Ge alloys using powder metallurgy for biomedical implants. The Ti–10Cr–2Ge alloy exhibits superior mechanical performance with high yield strength (>1100 MPa), low Young's modulus (<85 GPa), and excellent strain hardening behavior.
Teddy Sjafrizal, Damon Kent, Ali Dehghan‐Manshadi, Matthew S. Dargusch   +3 more
wiley   +1 more source

Machine Health Indicators and Digital Twins. [PDF]

Sensors (Basel)
Bublil T, Cohen R, Kenett RS, Bortman J.
europepmc   +1 more source

Titanium‐S23: A New Alloy with Ultra‐High Tensile Toughness Directly from the Solid‐State Processing of Recycled Ti–6Al–4V and Ti–5Al–5Mo–5V–3Cr Powders using Field Assisted Sintering Technology

Advanced Engineering Materials, EarlyView.
This study explores combining two existing aerospace titanium alloy powders, processing them via field‐assisted sintering technology and the subsequent discovery of a novel alloy composition, termed S23, with ultra‐high tensile toughness. Fine‐scale alpha precipitates favorably form in the alloy despite the relatively slow cooling, providing an ...
Samuel Lister, Gavin J. Baxter, Martin Jackson   +2 more
wiley   +1 more source

Energy Harvesting Microelectromechanical System for Condition Monitoring Based on Piezoelectric Transducer Ring. [PDF]

Micromachines (Basel)
Wang K, Long H, Song D, Shariar H.
europepmc   +1 more source

New Developments in the Field of Production and Application of Multi‐Material Wire Arc Additive Manufacturing Components: A Review

Advanced Engineering Materials, EarlyView.
The utilization of direct energy deposition (DED)‐arc additive manufacturing processes in industrial applications is increasing, and these processes have the potential for multi‐material applications. This work provides a overview of the state of research in DED‐arc made functional graded structures, to establish a link to potential industrial ...
Kai Treutler, Volker Wesling
wiley   +1 more source

Rotational Triboelectric Nanogenerator with Machine Learning for Monitoring Speed. [PDF]

Sensors (Basel)
Zhang C, Liu J, Shao Y, Ni X, Xie J, Luo H, Yang T.   +6 more
europepmc   +1 more source

Influence of Heat Treatment on Microstructure and Mechanical Properties at Elevated Temperatures of Nonweldable Ni‐Based Alloy Printed by Fused Filament Fabrication

Advanced Engineering Materials, EarlyView.
The fused filament‐fabricated MAR‐M247 alloy without hot isostatic pressing shows the lowest porosity of 4%. Heat treatment at 1220 °C produces coarse precipitates and carbides. Specimens heat‐treated at 1220 °C exhibit higher tensile strength (683 MPa) and elongation (10%) at room temperature.
Haneen Daoud, Ying Zheng, Agata Kulig, Natalja Agarkov, Esma Mese, Wolfgang Hofmann, Peter Würtele, Uwe Glatzel   +7 more
wiley   +1 more source

Vibration-based gearbox fault diagnosis using a multi-scale convolutional neural network with depth-wise feature concatenation. [PDF]

PLoS One
Nguyen VT, Diep QB.
europepmc   +1 more source

Investigation of Iron‐Aluminide‐Like Phase Composition in Complex Concentrated Fe32Cu12Ni11Ti16Al29 Alloy

Advanced Engineering Materials, EarlyView.
This work reveals the phase composition and quantitative morphology analysis of precipitation‐hardened Fe32Cu12Ni11Ti16Al29 complex‐concentrated alloy. The precipitates are shown to have a high coherency. Morphology transition between sphere, cuboidal, and elongated morphology is observed. Finally, the overaging behavior is captured using microhardness.
Rostyslav Nizinkovskyi, Lukas Hanisch, Georg Hasemann, Puspendu Sahu, Manja Krüger   +4 more
wiley   +1 more source