Results 201 to 210 of about 1,892,709 (308)

Low‐Cost, Large‐Scale Nanoporous Metals by Mechanical Alloying, Oxide Reduction, and Dealloying of Powders

Advanced Engineering Materials, EarlyView.
Powder metal processing provides scalable advantages in nanoporous (np) metal development. Mechanical alloying is used to produce unique precursors for hybrid nanopore formation by oxide reduction and dealloying. As demonstrated in np Ag, this approach improves process efficiency while promoting smaller ligaments and larger pores, both of which are ...
Mark A. Atwater, Oliver A. Fowler
wiley   +1 more source

Impact of Printing Angle and Layer Height on the Mechanical Strength of PLA Reinforced with Chopped Carbon Fibres Using FDM 3D Printing. [PDF]

Polymers (Basel)
Araque O, Sánchez-Echeverri LA, Cerón IX.   +2 more
europepmc   +1 more source

Material Strength and Applied Mechanics

, 2023
openaire   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Author Correction: Origin and tuning of bandgap in chiral phononic crystals

Communications Physics
Wei Ding, Rui Zhang, Tianning Chen, Shuai Qu, Dewen Yu, Liwei Dong, Jian Zhu, Yaowen Yang, Badreddine Assouar   +8 more
doaj   +1 more source

SWCNT/PEDOT:PSS/SA Composite Yarns with High Mechanical Strength and Flexibility via Wet Spinning for Thermoelectric Applications. [PDF]

Sensors (Basel)
Uchida K, Shinozaki Y, Nakayama H, Ochiai S, Nakazawa Y, Takashiri M.   +5 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Intratendinous Normal Saline Injection of Quadriceps and Patellar Tendon Allografts Does Not Reduce Mechanical Strength at Time Zero. [PDF]

Arthrosc Sports Med Rehabil
Jacquez EA, Zielinski KP, Etchart JM, Dawit L, Lucas SL, Perraut GT, Zittel KW, Saddler SC, Cunningham BW.   +8 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Degradation effects of reused PA12 powder in selective laser sintering on material characteristics, dimensional accuracy and mechanical strength. [PDF]

Sci Rep
Vendittoli V, Mascolo MC, Polini W, Walter MSJ, Sorrentino L, Sover A.   +5 more
europepmc   +1 more source