Results 161 to 170 of about 92,416 (256)

The In-Situ Mechanics of the Tricuspid Valve: Strain Heterogeneity and Anisotropy via 3D Digital Image Correlation. [PDF]

Exp Mech
LaRue TG, Haese CE, Pouch AM, Fuhg JN, Timek TA, Rausch MK.   +5 more
europepmc   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Mechanical properties and energy evolution characteristics of fissure sandstone under the interaction between water and fissures. [PDF]

PLoS One
He Q, Deng J, Yuan G.
europepmc   +1 more source

Applied Mathematics and Mechanical Engineering Problems [PDF]

The Open Mechanical Engineering Journal, 2018
openaire   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Spatial scale of indentation explains shift in ratio between spinal cord gray and white matter stiffness. [PDF]

Sci Rep
Neumann O, Surana HV, Hintze M, Kuerten S, Franz T, Ramachandran RG, Steinmann P, Budday S.   +7 more
europepmc   +1 more source

Characterization of Aluminized Layers on Inconel‐738 Alloy: Microstructure, Modeling of Aluminizing Kinetics, and Thermal Behavior

Advanced Engineering Materials, EarlyView.
This study explored how effective nickel aluminide coatings are obtained in providing oxidation resistance applied to the Inconel 738 alloy, modeling with diffusion models. In the present study, kinetics and thermal behavior of the Inconel 738 alloy were studied by the low‐temperature thermoreactive aluminizing process, which was carried out at 625°C ...
Gozde Celebi Efe, Tuba Yener, Suayb Cagri Yener, Mourad Keddam, Cuma Bindal   +4 more
wiley   +1 more source

Friction Modeling of Tendon-driven Continuum Robots through Linear Complementarity Problem. [PDF]

IEEE Robot Autom Lett
Shen J, Browne B, Ha J, Chen Y.
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source

Theoretical Considerations for Patient-Specific Modeling Based on Observable State Variables. [PDF]

J Biomech Eng
Ateshian GA, Deiters S, Weiss JA.
europepmc   +1 more source