Results 101 to 110 of about 3,074,199 (290)

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

open access: yesAdvanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel   +2 more
wiley   +1 more source

Influence of composition variations on microstructure and properties of SnBiInAl low-melting-point medium-entropy solder alloys

open access: yesHanjie xuebao
With the rapid development of three-dimensional integrated packaging technology, higher requirements have been put forward for the performance and reliability of low-temperature lead-free solders.
Yan GAO   +6 more
doaj   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

open access: yesAdvanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt   +4 more
wiley   +1 more source

Manufacture and characterization of HoErCo medium-entropy alloy microwires with excellent magnetic entropy change

open access: yes, 2021
A melt-extracted HoErCo medium-entropy alloy (MEA) with large magnetic entropy change and excellent magnetic refrigerant capacity is successfully designed in this study. The microstructure evolution of these microwires near room temperature is studied by
Li, Ze   +13 more
core   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

open access: yesAdvanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar   +3 more
wiley   +1 more source

Microstructure‑Dependent Phase Transformations Under High‑Pressure Laser Heating in Additively Manufactured AlCrFe2Ni2

open access: yesAdvanced Engineering Materials, EarlyView.
Additively manufactured AlCrFe2Ni2 with contrasting BCC/B2‐dominant and lamellar FCC + BCC/B2 microstructures exhibits the same pressure‐induced BCC/B2 → HCP transformation. Under laser heating at high pressure, HCP is destabilized, and a cubic BCC/B2 + FCC assemblage is recovered, while the lower‐scan‐speed microstructure transforms at a lower ...
Raimundas Sereika   +5 more
wiley   +1 more source

Investigation on the energy absorption characteristics of medium entropy alloy thin-walled tubes under dynamic impact

open access: yesJournal of Materials Research and Technology
In this study, innovative conceptual designs of thin-walled tubes comprised of VNbTa medium entropy alloy are proposed, and their deformation modes and energy absorption characteristics under quasi-static and dynamic impact conditions are systematically ...
Zhao Zhang   +6 more
doaj   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

open access: yesAdvanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo   +15 more
wiley   +1 more source

Low cycle fatigue predictions of a space thruster built with a new refractory high entropy alloy [PDF]

open access: yes, 2023
Directional thrusters are designed to provide force for short time periods. • New generation of thrusters could be made using a High Entropy Alloy (HEA).
Canale, G.   +3 more
core  

Microstructural, Mechanical, and Textural Evolution of Dissimilar Combination of Laser‐Welded Maraging Steel and 4340 Steel

open access: yesAdvanced Engineering Materials, EarlyView.
The present work reports the microstructural, mechanical, and texture evolution of a dissimilar combination laser‐welded maraging steel with 4340 steel. This is important for aerospace applications. The demand for dissimilar welding is growing rapidly with the requirement of efficient and durable joints.
Bharat Behl   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy