Results 11 to 20 of about 4,838 (181)
The MRP4 transporter exports several drugs and signaling molecules. Here, we identified key promoter elements regulating basal MRP4 expression. Using reporter assays, we defined a conserved region with essential Sp1 and contributory Ets sites, which controlled basal MRP4 expression.
Debora Singer +7 more
wiley +1 more source
Thermomechanical fatigue tests of laser beam powder bed fusion (PBF‐LB) Inconel 718 show that the additively manufactured material reaches almost the lifetimes of conventionally‐rolled material under no‐dwell conditions. Introducing dwell times at the maximum temperature markedly reduces the lifetimes due to pronounced grain boundary sliding associated
Stefan Guth +6 more
wiley +1 more source
Creating Ti–Fe α/β Alloys by Diffusion‐Driven Solid‐State Processing
This study proposes making alloys containing fast diffusing elements that are difficult to produce by ingot metallurgy, by diffusion‐driven solid‐state HIP processing of elemental powders and low‐temperature homogenisation. Here, novel Fe‐Ti α–β alloys are formed having fine α–β lamellae, a small β prior grain size without significant intermetallics ...
Jiaqi Xu +10 more
wiley +1 more source
The geothermal energy of the Yingjiang basin is located within Yingjiang–Longchuan high-temperature hot water belt, which is part of Gaoligongshan–Tengchong sub-area of high-temperature hot water region of western Yunnan.
Hua ZHANG +7 more
doaj +1 more source
Time‐Dependent Oxidation and Scale Evolution of a Wrought Co/Ni‐Based Superalloy
This study shows how a new wrought Co/Ni‐based superalloy resists oxidation at 800 ∘$^\circ$C. The oxide scale changes from rough, fast‐growing spinel to a dense, protective chromia–alumina layer. Atom probe analysis reveals tiny refractory‐rich bubbles at the interface that mark the transition to long‐term, diffusion‐controlled protection ...
Cameron Crabb +6 more
wiley +1 more source
Identified through the use of statistical design of experiments and metallographic investigation, this study exposes the stochastic origins of intergranular cracks in blown powder laser beam directed energy deposition additive manufacturing of pure molybdenum. It further demonstrates a successful crack mitigation approach with direct correlation to the
Nathaniel J. Lies +2 more
wiley +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
This study shows that superalloys used in aircraft engine disks become much more prone to deformation at high temperatures if they have been strained during manufacturing. This effect increases with the level of prior strain but eventually reaches a limit.
Fabio Machado Alves da Fonseca +9 more
wiley +1 more source
Hydrochemical characteristics and genesis of geothermal water in the Zunyi area, north Guizhou
The Zunyi area in north Guizhou is located on the slope section transiting from the Yunnan-Guizhou Plateau to the Sichuan Basin. This area is geotectonically situated on the southwestern margin of the Yangzi plate, where Neoproterozoic strata to Cenozoic
Wei LUO +6 more
doaj +1 more source
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source

