Results 51 to 60 of about 242,519 (306)
Strengthening mechanisms in vanadium-microalloyed medium-Mn steels
Materials Today CommunicationsPeer ...
Zvavamwe, Felisters +4 more
openaire +2 more sources
Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics
Advanced Engineering Materials, EarlyView.Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost +4 more
wiley +1 more source
The combined effect of chemical composition and cooling rate on transformation temperatures of hypoeutectoid steels [PDF]
, 2018 The transformation temperatures A(r3) and A(r1) of four unalloyed hypoeutectoid steels with a carbon content of 0.029-0,73 % were determined using dilatometric tests.
Kawulok, Petr +6 more
core +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source
Effect of cerium concentration on corrosion resistance and polymerization of hybrid sol–gel coating on martensitic stainless steel [PDF]
, 2012 Stainless steels are increasingly used in the aeronautics field for the manufacture of structural parts. One of them, the X13VD martensitic stainless steel (X12CrNiMoV12-3), known for its good mechanical properties, has a poor corrosion resistance in ...
Ansart, Florence +3 more
core +3 more sources
Advanced Engineering Materials, EarlyView.EDX elemental map of the pre‐oxidized MgO–steel cermet anode cross section after electrolysis. The development of inert anodes for aluminum electrolysis remains challenging due to the high corrosivity of cryolite‐based melts at 950°C–1000°C. This study investigates the corrosion and process behavior of a carbon‐free MgO–steel cermet anode derived from ...
Alexander Adamczyk +7 more
wiley +1 more source
Microbial electrocatalysis with Geobacter sulfurreducens biofilm on stainless steel cathodes [PDF]
, 2008 Stainless steel and graphite electrodes were individually addressed and polarized at−0.60V vs. Ag/AgCl in reactors filled with a growth medium that contained 25mM fumarate as the electron acceptor and no electron donor, in order to force the microbial ...
Afkar +21 more
core +1 more source
Advanced Engineering Materials, EarlyView.Micro‐Raman spectroscopy is applied to characterize corrosion products in a recycled‐based MgO–316L steel composite anode after molten salt electrolysis. A depth‐dependent Fe–O/Fe–Al–O layer sequence of magnetite, hercynite, and an Al‐doped magnetite transition zone is identified.
Felix Drechsler +9 more
wiley +1 more source
Optimising the laser-welded butt-joints of medium carbon steel using RSM [PDF]
, 2005 The optimization capabilities in design-expert software were used to optimise the keyhole parameters (i.e. maximize penetration (P) and minimise the heat input, width of welded zone, (W) and width of heat affected zone (WHAZ)) in CW CO2 laser butt ...
Benyounis, Khaled +2 more
core +1 more source
Application of Quenching and Partitioning Processing to Medium Mn Steel [PDF]
Metallurgical and Materials Transactions A, 2014 The present work analyzes the application of quenching and partitioning processing to medium Mn steel to obtain a new type of ultra-high-strength multiphase medium Mn steel. The selection of the quench temperature makes it possible to vary the ultimate tensile strength within a range of 500 MPa. The processing leads to low-carbon lath martensite matrix
Seo, EJ, Cho, L, De Cooman, BC
openaire +2 more sources