Results 261 to 270 of about 10,404 (304)
Some of the next articles are maybe not open access.
Experimental Investigation on Inclusions in Medium Manganese Steels and High Manganese Steels
2021Doctor of Philosophy (PhD)
openaire +2 more sources
Warm Stamping Technology of the Medium Manganese Steel
steel research international, 2017A kind of hot stamping technology with lower heating temperature, as named as warm stamping, is proposed based on the medium manganese steel. The differences on the microstructure and mechanical properties among 22MnB5 steel, Al–Si coated 22MnB5 steel, and medium manganese steel are studied before and after hot/warm stamping process based on industrial
Cunyu Wang +6 more
openaire +1 more source
Cementite evolution in medium manganese twinning-induced plasticity steels
Materialia, 2018Abstract The precipitation and dissolution of cementite in austenitic medium Mn high C steels capable of deformation-induced twinning were studied based on the associated length changes. In continuous dilatometry heating cycles, the net contraction associated with the precipitation of cementite resulted in a decrease in the apparent coefficient of ...
Javad Mola +4 more
openaire +1 more source
On the transformation-induced plasticity of a medium-manganese steel
Materials Letters, 2021Abstract The mechanical behavior assisted by transformation-induced plasticity was studied in an Fe-0.2%C-10%Mn steel. The starting material was subjected to large strain warm rolling at 550 °C, which corresponds to two phase region with austenite and ferrite as 50:50.
V. Torganchuk, A. Belyakov, R. Kaibyshev
openaire +1 more source
Austenite transformation and work hardening of medium manganese steel
Journal of Iron and Steel Research International, 2018The austenite transformation behavior and mechanical properties of medium manganese steel subjected to tensile strain were studied by electron backscatter diffraction, X-ray diffraction and tensile tests. The results show that the austenite phases are mainly distributed on the grain boundary in the duplex microstructure of austenite and ferrite, and it
Lei Zhang +6 more
openaire +1 more source
Eutectic growth in as-cast medium manganese steel
Materials Science and Engineering: A, 2002Abstract Eutectic growth in as-cast medium manganese steel modified by a Mg–Ce–Ti–Si compound was investigated by means of transmission electron microscopy (TEM), scanning electron microscopy (SEM) and electron probe microanalysis (EPMA). Results show that the eutectic ((Fe, Mn) 3 C and austenite) is formed between austenite dendrites at the end of ...
openaire +1 more source
Mechanical response of a medium manganese steel with encapsulated austenite
Scripta Materialia, 2020Abstract Encapsulated microstructures of austenite and co-precipitates were formed using a designed tempering and double partitioning (TDP) heat treatment based on the precipitation-induced localized austenite reversion in a medium manganese (Mn) steel.
Yong Li +5 more
openaire +1 more source
Materials Science and Engineering: A, 2018
Abstract Manganese is normally considered as the most important alloying element in medium Mn steels. However, the influence of Mn additions on the microstructural characteristics and the ensuring mechanical properties has not been much studied.
Binhan Sun +7 more
openaire +1 more source
Abstract Manganese is normally considered as the most important alloying element in medium Mn steels. However, the influence of Mn additions on the microstructural characteristics and the ensuring mechanical properties has not been much studied.
Binhan Sun +7 more
openaire +1 more source
On friction stir welding of a medium manganese austenitic steel
Philosophical Magazine, 2020The plates of an Fe–12%Mn–0.5%C–1.5%Al austenitic steel with an original grain size of 80 µm were subjected to friction stir welding using a spherical welding pin.
Vladimir Torganchuk +4 more
openaire +1 more source
Solid State Phase Transformations in Medium Manganese Steels
2018Steels are still, and probably will remain in future, the primary choice for applications as structural materials. This is not only because of the reasonable ratios of properties over production costs, but also owing to the versatile properties realisable via variety of microstructures achieved by controlling the solid-state phase transformations ...
openaire +3 more sources