Results 41 to 50 of about 20,369 (268)
Advanced Engineering Materials, EarlyView.A two‐step approach combining laser powder bed fusion of FeSi electrical steel with Bakelite infiltration enables the fabrication of multifunctional gyroid lattice composites. The resulting structures exhibit high strength, magnetic anisotropy, and complete polymer infiltration, demonstrating a simple and scalable route toward lightweight, mechanically
Angelo F. Andreoli +9 more
wiley +1 more source
INFLUENCE OF WORKING MEDIUM LEAKS ON THE POINT POSITION OF MAXIMUM COMPRESSION PRESSURE RISE RATE
Авіаційно-космічна техніка та технологія, 2019 The article discusses the analysis of the parameters of the compression process, which is carried out according to the results of engine indication. The solution to this problem allows us to evaluate the technical condition of the cylinder-piston group ...
Алексей Валериевич Ерыганов +2 more
doaj +1 more source
Energies, 2021 Nowadays, increasingly stricter regulations on emission reduction are inducing rapid developments in combustion science. Low-temperature combustion (LTC) is an advanced combustion technology that increases an engine’s thermal efficiency and even provides
Márton Virt +4 more
doaj +1 more source
Internal Temperature Evolution Metrology and Analytics in Li‐Ion Cells
Advanced Functional Materials, EarlyView.This study investigates the non‐linear evolution of internal temperatures across diverse operating conditions, highlighting the disparities between internal and external measurements and the resulting thermal asymmetries. The coupled thermo‐electrochemical modeling framework provides a comprehensive analysis of various heat generation modes, examining ...
Anuththara S. J. Alujjage +5 more
wiley +1 more source
Energies, 2022 Nowadays, the noise pollution of internal combustion engines is a very important factor influencing human health and is the main noise source of urban environmental noise.
Zhenbin Chen +4 more
doaj +1 more source
Advanced Functional Materials, Volume 35, Issue 12, March 18, 2025.By fabricating and covalently assembling gelatin methacryloyl (GelMA) porous microgels, a new class of granular hydrogel scaffolds with hierarchical porosity is developed. These scaffolds have a significantly higher void fraction than their counterparts made up of nonporous microgels, enhancing cell recruitment and tissue integration. This research may
Alexander Kedzierski +9 more
wiley +1 more source
Energies, 2019 The effect of iron-doped cerium oxide (FeCeO2) nanoparticles as a fuel additive was experimentally investigated with waste cooking oil methyl ester (WCOME) in a four-stroke, single cylinder, direct injection diesel engine.
Meshack Hawi +3 more
doaj +1 more source
Zhongguo youzhi, 2023 为探究生物柴油在船舶柴油机上的适用性，基于六缸中速柴油机试验台架，在不同负荷推进特性工况下，对燃用0#柴油、B10生物柴油柴油机的动力性能、经济性能、振动特性和缸内燃烧特性进行对比分析。结果发现：与0#柴油相比，燃用B10生物柴油柴油机的输出功率和耗油量基本不变，耗油率有所升高，但随着负荷的升高有所改善,燃用B10生物柴油使得在25%负荷工况下的柴油机缸盖振动烈度下降，50%、75%、90%、100%负荷工况下的柴油机缸盖振动烈度稍有上升，不同负荷工况下的机体振动烈度均下降；从振动功率谱密度可以看出 ...
张哲1，江国和1，陈优金2，吴刚1 ZHANG Zhe1, JIANG Guohe1, CHEN Youjin2, WU Gang1
doaj +1 more source
Advanced Functional Materials, EarlyView.This work explores Li‐substituted P2 layered oxides for Na‐ion batteries by crystallographic and electrochemical studies. The effect of lithium on superstructure orderings, on phase transitions during synthesis and electrochemical cycling and on the interplay of O‐ versus TM‐redox is revealed via various advanced techniques, including semi‐simultaneous
Mingfeng Xu +5 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Biofabrication aims at providing innovative technologies and tools for the fabrication of tissue‐like constructs for tissue engineering and regenerative medicine applications. By integrating multiple biofabrication technologies, such as 3D (bio) printing with fiber fabrication methods, it would be more realistic to reconstruct native tissue's ...
Waseem Kitana +2 more
wiley +1 more source