Results 191 to 200 of about 744,006 (340)

Multi-Conformation Enhanced Equivariant Graph Neural Network: Advancing Melting Point Prediction Accuracy for Organic Small Molecules. [PDF]

ACS Omega
Huang T, Yang Z, Gao M, Pan L, Wang L, Ding J.   +5 more
europepmc   +1 more source

Development of a low-melting-point eutectic salt and evaluation of its discharge performance for light weight thermal batteries. [PDF]

RSC Adv, 2022
Ahn TY, Cheong HW, Kang SH, Lee JI, Kim M, Choi Y.   +5 more
europepmc   +1 more source

Effect of Laser Scanning Conditions on Four-point Bending Fatigue Properties of Ti-6Al-4V Fabricated by Selective Laser Melting

, 2019
Shoichi Kikuchi, Kohei OSAKI, Yoshikazu NAKAI, Shinji Ishibashi, Keita Shimada, Masayoshi Mizutani, Tsunemoto Kuriyagawa   +6 more
openalex   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Development of a new poly-ε-caprolactone with low melting point for creating a thermoset mask used in radiation therapy. [PDF]

Sci Rep, 2021
Aoyama T, Uto K, Shimizu H, Ebara M, Kitagawa T, Tachibana H, Suzuki K, Kodaira T.   +7 more
europepmc   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Laser Cladding for Diamond-Reinforced Composites with Low-Melting-Point Transition Layer. [PDF]

Materials (Basel)
Chen Y, Du Y, Liu J, Zhang S, Wang T, Guo S, Cui Y, Li X, Zheng B, Zhao Y, Cui L.   +10 more
europepmc   +1 more source

A Rapid Thermal Absorption Rate and High Latent Heat Enthalpy Phase Change Fiber Derived from Bio-Based Low Melting Point Copolyesters. [PDF]

Polymers (Basel), 2022
Lan TY, Mao HI, Chen CW, Lee YT, Yang ZY, Luo JL, Li PR, Rwei SP.   +7 more
europepmc   +1 more source

Perspective Chapter: Boiling Point, Melting Point, Freezing Point – Water Is the Essence of Life, and What We Need to Do to Avert Calamity

Oluwafikemi Iji, Oluwatisheyitoju Iji
openalex   +2 more sources

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source