Results 111 to 120 of about 4,709 (265)
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source
Study on the Dynamics of Non-circular Planetary Gear Hydraulic Motor
Jixie chuandong, 2017 The structure and working principle of a new type of non-circular planetary gear hydraulic motor are introduced. The pitch curve and tooth profile of each gear within non-circular planetary gear system are programmed. A torsional vibration model is built
Wei Shuang, Li Dianqi, Liu Guanghui
doaj
Advanced Engineering Materials, EarlyView.This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome +6 more
wiley +1 more source
Analysis of Vibration Characteristic of the ZC1 Worm Gear Reducer
Jixie chuandong, 2018 In order to reduce the vibration and noise of the ZC1 worm gear transmission,it needs to make a study of its dynamic characteristics. Based on the theory of the lumped mass method,the dynamical analysis model of the ZC1 worm gear reducer transmission ...
Ma Yujuan +3 more
doaj
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Drive Stability Analysis of Main Reducer of Forklift Drive Axle
Jixie chuandong, 2015 First of all,the 3Dmodeling of spiral bevel gear is conducted by using SolidWorks software.Then,based on Hertz contact theory,a virtual prototype model of spiral bevel gear for forklift main reducer is established by using ADAMS,through simulation ...
Wei Liangbao +4 more
doaj
Hybrid Metal–Carbon Ink for Printed Stretchable Temperature Sensors
Advanced Engineering Materials, EarlyView.We prepare conductive inks for temperature sensing with silver flakes and carbon or graphite flakes in a silicone elastomer matrix. Silver dominates the temperature‐dependent conductivity, while the carbon filler network ensures the stability of the conductive pathways and retains function under strain.
Makara Lay +3 more
wiley +1 more source
Jixie chuandong, 2014 According to the processing method and meshing theory,the equation of the asymmetric face gear is deduced.Asymmetric and symmetric face gear drive model are established by Pro/E, the analysis is carried out through importing them to ABAQUS.The material ...
严宏志 +4 more
doaj
Enhancing Low‐Temperature Performance of Sodium‐Ion Batteries via Anion‐Solvent Interactions
Advanced Functional Materials, EarlyView.DOL is introduced into electrolytes as a co‐solvent, increasing slat solubility, ion conductivity, and the de‐solvent process, and forming an anion‐rich solvent shell due to its high interaction with anion. With the above virtues, the batteries using this electrolyte exhibit excellent cycling stability at low temperatures. Abstract Sodium‐ion batteries
Cheng Zheng +7 more
wiley +1 more source
Laser‐Induced Graphene from Waste Almond Shells
Advanced Functional Materials, EarlyView.Almond shells, an abundant agricultural by‐product, are repurposed to create a fully bioderived almond shell/chitosan composite (ASC) degradable in soil. ASC is converted into laser‐induced graphene (LIG) by laser scribing and proposed as a substrate for transient electronics.
Yulia Steksova +9 more
wiley +1 more source