Results 81 to 90 of about 9,298 (261)
Engineering Science and Technology, an International JournalTo enhance the meshing characteristics of the face gear pair and determine the optimal modification parameters, an optimization model of modification parameters, based on the TCA-NRBPNN-HYPE (Tooth Contact Analysis-Newton Raphson Back Propagation Neural ...
Kun He +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.A two‐dimensional multiscale finite element analysis framework was established for the first‐generation MoSiBTiC alloy, and the mechanical and fracture‐related parameters of the constituent phases were calibrated through experiments and simulations. The framework provides a basis for analyzing crack propagation behavior in its complex microstructure ...
Junfeng Du +4 more
wiley +1 more source
Hydrogen‐Assisted Fracture of Iron‐Based Fe–Ni–Al Alloys
Advanced Engineering Materials, EarlyView.Principal relations and fracture mechanisms of single‐phase and precipitate‐strengthened Fe–Ni–Al alloys subjected to prior electrochemical hydrogen charging are identified. The mechanisms of hydrogen effect on strength and microhardness are discussed, including hydrogen‐induced increase in microhardness and the role of hydrogen in fracture behavior ...
Nataliya Yadzhak +3 more
wiley +1 more source
Jixie chuandong, 2021 When a gear has a pitting fault，the vibration response characteristics caused by its time-varying meshing stiffness change is an important basis for the diagnosis of pitting faults，and an accurate gear geometry model is of great significance for the ...
Chaoyang Jiang, Yanxue Wang, Junjie Lai
doaj
Advanced Engineering Materials, EarlyView.Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari +5 more
wiley +1 more source
On the Meshing Efficiency of 2K-2H Type Planetary Gear Reducer
Advances in Mechanical Engineering, 2013 This paper proposes 2K–2H type planetary gear reducer and analyzes its meshing efficiency. First, according to the concept of train value equation, the kinematic design of 2K–2H type planetary gear reducers is carried out. Three 2K–2H type planetary gear
Long-Chang Hsieh, Hsiu-Chen Tang
doaj +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application
Advanced Engineering Materials, EarlyView.N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang +4 more
wiley +1 more source
工程科学与技术, 2020 With the wide use of helical planetary gears in the case of high-speed and heavy loads, the study of dynamic loads characteristics become great significance for reduction vibration and noises.
Jinke JIANG, Zongde FANG, Hongmei LIU
doaj
Advanced Engineering Materials, EarlyView.Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal +3 more
wiley +1 more source