Results 91 to 100 of about 70,843 (305)
A basis for the analysis of surface geometry of spiral bevel gears [PDF]
, 1983 Geometrical procedures helpful in the fundamental studies of the surface geometry of spiral bevel gears are summarized. These procedures are based upon: (1) fundamental gear geometry and kinematics as exposited by Buckingham, et al; (2) formulas ...
Coy, J. J., Huston, R. L.
core +1 more source
Advanced Engineering Materials, EarlyView.Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek +5 more
wiley +1 more source
Design and finite element mode analysis of noncircular gear [PDF]
, 2008 The noncircular gear transmission is an important branch of the gear transmission, it is characterized by its compact structure, good dynamic equilibration and other advantages, and can be used in the automobile, engineering machine, ship, machine tool ...
Cheng, K +5 more
core
Advanced Engineering Materials, EarlyView.Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller +6 more
wiley +1 more source
Accuracy Improvement for Stiffness Modeling of Parallel Manipulators [PDF]
, 2009 The paper focuses on the accuracy improvement of stiffness models for parallel manipulators, which are employed in high-speed precision machining. It is based on the integrated methodology that combines analytical and numerical techniques and deals with ...
Chablat, Damien +3 more
core +4 more sources
Advanced Engineering Materials, EarlyView.A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora +4 more
wiley +1 more source
Jixie chuandong, 2019 The meshing backlash of cycloidal-pin gear has a great influence on the meshing transmission performance and motion accuracy of RV reducer, so the accurate calculation of meshing backlash is an important content in the study of contact characteristics of
Tianxing Li +4 more
doaj
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Solcore: A multi-scale, python-based library for modelling solar cells and semiconductor materials
, 2018 Computational models can provide significant insight into the operation mechanisms and deficiencies of photovoltaic solar cells. Solcore is a modular set of computational tools, written in Python 3, for the design and simulation of photovoltaic solar ...
Alonso-Álvarez, D. +5 more
core +1 more source
2D Hexagonal Mesh Vs 3D Mesh Network on Chip: A Performance Evaluation
International Journal of Computing and Digital Systems, 2015 D Network on Chip (NoC) has emerged as a new platform to meet the performance requirements and scaling challenges of System on Chip. More investigations require addressing challenges in multiport topologies, minimizing foot printing of nodes and interconnections of wires. This paper discusses multi-port NoC topologies and routing in 2D hexagonal and 3D
openaire +1 more source