Results 101 to 110 of about 65,517 (305)
Jixie chuandong, 2022 To improve the comprehensive dynamic meshing performance of a certain gear product， a design method for controlling the polynomial coefficients of the topological modification of the tooth surface is proposed.
Jiaqi Li, Congcong Song, Bingyang Wei
doaj
3D‐Printed Giant Magnetoresistive (GMR) Sensors Based on Self Compliant Springs
Advanced Engineering Materials, EarlyView.This work explores 3D‐printed GMR sensors utilizing self‐compliant spring structures and conductive PLA composites. By optimizing arm width, we achieved high piezoresistive (0.34%/mm) and magnetoresistive (0.77%/mT) sensitivities. Demonstrated through Bluetooth‐integrated pressure and magnetic position sensing, these full printed low‐cost, customizable
Josu Fernández Maestu +4 more
wiley +1 more source
MESHING STIFFNESS ANALYSIS OF CYCLOID STEEL BALL MESHING PAIR BASED ON THERMAL DEFORMATION
Jixie qiangdu, 2019 In order to study the influence of thermal deformation of the cycloid ball meshing pair on dynamic performance of the precision ball transmission, the thermal deformation of contact point of the cycloid ball meshing pair was analyzed by the Green ...
LIU XiangHui, AN ZiJun
doaj
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Finite Element Simulation Analysis for Dynamic Meshing Force of Straight Tooth Face Gear
Jixie chuandong, 2015 Analysis of the dynamic meshing force of face gear is the important content in the design of face gear drive with high quality.Based on the secondary development of CATIA and the principle of gear machining,the 3Dgeometric modeling of face gear for ...
Cao Maopeng, Tang Jinyuan, Lei Duncai
doaj
Advanced Engineering Materials, EarlyView.Four‐point bending tests are conducted in an argon atmosphere on commercial MgO‐C brick grades with and without MgO‐C recyclate from room temperature up to 1300 °C. No detrimental effect of the MgO‐C recyclates on bending strength is found. Instead, a decisive influence of the total carbon content is observed, with lower total carbon contents ...
Alexander Schramm +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.This study investigates thermo‐chemical processes during high‐temperature testing of two commercial MgO‐C brick grades, one containing 47.5 wt.% MgO‐C recyclate. Using ETV, DTA/TG‐MS, XRD, and SEM/EDS/EBSD, mechanisms such as carbothermal reduction of magnesia, impurity incorporation into the secondary MgO surface layer, and calcium‐rich phase ...
Alexander Schramm +6 more
wiley +1 more source
Research on Dynamic Performance of Locomotive Wheelset Driving Unitwith Gear Teeth Cracks
机车电传动, 2016 In order to simulate the influences of gear teeth cracks on the dynamic performance of the wheelset driving system, withthe multi-body dynamic software SIMPACK, the vibration model of gear-pair meshing was established, which, meanwhile, was appliedto the
FAN Jiafeng +3 more
doaj
Jixie chuandong, 2021 The meshing temperature of plastic gear affects the mechanical behaviors such as fatigue， wear and noise， which should not be ignored in the mechanical response and performance prediction of plastic gear.
Guoda Yu +4 more
doaj
A basis for the analysis of surface geometry of spiral bevel gears [PDF]
, 1983 Geometrical procedures helpful in the fundamental studies of the surface geometry of spiral bevel gears are summarized. These procedures are based upon: (1) fundamental gear geometry and kinematics as exposited by Buckingham, et al; (2) formulas ...
Coy, J. J., Huston, R. L.
core +1 more source