Results 61 to 70 of about 77,459 (311)
Faster - Better Molds Through RSP Tooling New Research and Advancements [PDF]
, 2004 The recent developments in rapid production tooling have all but made the need for prototype tooling disappear. There are several approaches that are now as fast and inexpensive as prototype tooling, and after part approval can continue to run in high ...
Knirsch, James R.
core +1 more source
Advanced Engineering Materials, EarlyView.This article presents a solver‐agnostic domain‐specific language (DSL) for computational structural mechanics that strengthens interoperability in virtual product development. Using a hierarchical data model, the DSL enables seamless exchange between diverse simulation tools and numerical methods.
Martin Rädel +3 more
wiley +1 more source
Joining lead wires to thin platinum alloy films [PDF]
, 1983 A two step process of joining a lead wire to .000002 m thick platinum alloy film which rests upon an equally thin alumina insulating layer which is adhered to a metal substrate is described.
Claing, R. G., Przybyszewski, J. S.
core +1 more source
What Do Large Language Models Know About Materials?
Advanced Engineering Materials, EarlyView.If large language models (LLMs) are to be used inside the material discovery and engineering process, they must be benchmarked for the accurateness of intrinsic material knowledge. The current work introduces 1) a reasoning process through the processing–structure–property–performance chain and 2) a tool for benchmarking knowledge of LLMs concerning ...
Adrian Ehrenhofer +2 more
wiley +1 more source
The effect of heat treatment on bonding strength of ceramic to cast nickel⁃chromium⁃based alloys
口腔疾病防治, 2016 Objective To explore the effect of heat treatments on the metal⁃ceramic bonding strength in Ni⁃Cr⁃Ti al⁃ loy and Ni⁃Cr alloy. Methods We evaluated the metal⁃ceramic bond strengths by using a three⁃points bending test ac⁃ cording to ISO 9693. Meanwhile,
LIN Shi-yao +5 more
doaj +1 more source
Development and design of binder systems for titanium metal injection molding: An overview [PDF]
, 2012 Titanium metal injection molding (Ti-MIM) has been practiced since the late 1980s. Logically, the Ti-MIM practice follows the similar processes developed for the antecedent materials such as stainless steel and ceramics.
Cao, Peng +4 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Journal of Applied Oral Science, 2003 A fim de avaliar a opinião da classe odontológica sobre a utilização das coroas metalo-cerâmicas na prática odontológica, aplicou-se um questionário de 20 questões a cirurgiões-dentistas da cidade de Aracaju - SE, e a cirurgiões-dentistas e estudantes de
Carlos Neanes Santos +2 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh +3 more
wiley +1 more source
Progress in Materials and Metal Substrates for Solid Oxide Fuel Cells
EnergiesSolid oxide fuel cells (SOFCs) have been considered as alternative energy conversion devices because of their high energy conversion efficiency, fuel flexibility, and cost efficiency without precious metal catalysts.
Young-Wan Ju
doaj +1 more source