Results 101 to 110 of about 87,517 (302)

Processing and characterization of monoclinic-zirconia fibre-matrix interfaces in dense matrix alumina-alumina composites: Processamento e caracterização de interfaces fibra-matriz de zircônia não estabilizada em compósitos alumina-alumina de matriz densa [PDF]

, 2013
Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico, Programa de Pós-Graduação em Engenharia Mecânica, Florianópolis, 2013.Interfaces fibra-matriz tem um papel muito importante no desempenho de compósitos de matriz ...
Blaese, Diego
core  

Formation and characterization of a nickel-quasicrystal composite produced by electroforming [PDF]

, 2001
The electroforming of metal matrix composites has been a research topic for more than a decade. Different types of reinforcement (e.g. SiC, Al 2O 3 and PTFE) have been used for different purposes such as wear resistance, dry lubrication, anticorrosion ...
Qu, NS, Chan, KC, K.C. Chan, N.S. Qu
core   +1 more source

Strengthening dual-phase Mg-Li alloy through precipitation control

Materials Research Letters
Inherent low strength is the major limitation of Mg-Li alloys. Through precise control of precipitates, the cast Mg-8Li-3Al-2Zn alloy obtained a high specific ultimate tensile strength of 213 kN·m·kg−1.
Yuchuan Huang, Fangzhou Qi, Jiawei Sun, Yangyang Xu, Youjie Guo, Jiaxin Yu, Lingfan Yi, Xinmiao Tao, Guohua Wu, Wencai Liu   +9 more
doaj   +1 more source

A super high-strength Mg-Gd-Y-Zn-Mn alloy fabricated by hot extrusion and strain aging

Materials & Design, 2019
A super high-strength wrought Mg-12.6Gd-1.3Y-0.9Zn-0.5Mn (GWZ1311M, wt%) alloy fabricated by hot extrusion and strain aging is developed. The strain before aging including cold rolling or cold rolling plus stretching results in strong work hardening and ...
Xiangwen Heng, Yu Zhang, Wei Rong, Yujuan Wu, Liming Peng   +4 more
doaj   +1 more source

Tailoring Functional Properties of Ti–Ni–Cu Shape Memory Alloy Thin Films for MEMS Actuators

Advanced Engineering Materials, EarlyView.
A comprehensive study of critical parameters required to develop well‐performing Ti–Ni–Cu thin film shape memory alloy microactuators is provided. Materials science and device integration aspects are integrated by addressing structural and physical relationships using complementary characterization techniques as well as a practical fabrication solution
Elaheh Akbarnejad, Aleksander Kostka, Gowtham Arivanandhan, Yujiao Li, Alan Savan, Manfred Kohl, Alfred Ludwig   +6 more
wiley   +1 more source

Influence of alloying elements on hot tearing susceptibility of Mg–Zn alloys based on thermodynamic calculation and experimental

Journal of Magnesium and Alloys, 2018
Based on the hot tearing index |∆T/∆(fs)0.5| recently proposed by Kou and the thermodynamic calculations of Pandat software, Al, Cu, and Mn elements were picked up and their influence on hot tearing susceptibility of Mg–xZn (x = 6, 8, 10, wt%) alloys was
Zhenzhen Yang, Ke Wang, Penghuai Fu, Liming Peng, Bin Hu, Ming Liu, Anil K. Sachdev   +6 more
doaj   +1 more source

Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy

Advanced Engineering Materials, EarlyView.
A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang, Aparajita Pramanik, Sandipan Sen, Shubhashis Dixit, Marcel Muench, R. J. Vikram, Daniel Schliephake, Yolita M. Eggeler, Ankur Chauhan, Martin Heilmaier, Alexander Kauffmann   +10 more
wiley   +1 more source

Process optimisation of non-cyanide Ag–PTFE metal matrix composite electroplating for threaded connections [PDF]

, 2015
Silver-PTFE metal matrix composite coatings were deposited onto ANSI 304 stainless steel to assess the potential of using a novel non-cyanide electroplating process to produce a corrosion resistant, self-lubricating composite coating.
Le, HR, Sieh, R, Sieh, Raymond, Le, H. R., Le, Huirong, Cree, Alistair, Cree, A, Cree, A. M., Sieh, R.   +8 more
core   +1 more source

Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A

Advanced Engineering Materials, EarlyView.
The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han, Julian M. Rosalie, Jan Radners, Mauro Madia, Philipp von Hartrott, Birgit Skrotzki   +5 more
wiley   +1 more source

Microstructure and mechanical properties of aluminium based nanocomposites strengthened with alumina and silicon carbide [PDF]

, 2014
Al-Al₂O₃ and Al-4wt%Cu-SiC metal matrix nanocomposites were studied because these materials have a potential for offering good ductility, high strength, and high electrical and/or thermal conductivity, which make them ideal for engineering applications ...
Gazawi, Amro Abdul-Karim
core