Results 191 to 200 of about 46,143 (280)

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Pressure-Induced Metallization and Isostructural Transitions in 3R-MoS₂. [PDF]

Adv Sci (Weinh)
Ahmad AS, Bhullar M, Stahl K, Lu W, Chen T, Feng L, Hu X, Zhang Q, Glazyrin K, Kunz M, Zhao Y, Wang S, Yao Y, Stavrou E.   +13 more
europepmc   +1 more source

On‐Demand Activation of Thin Alginate Shell Encapsulated Volatile Liquid for Untethered Pneumatic Soft Actuation

Advanced Engineering Materials, EarlyView.
Phase‐changing liquids enable untethered pneumatic actuation in soft robotics but suffer from volatility and storage challenges. This work reports a simple method to encapsulate Novec 7000 within micron‐thin alginate shells via in situ injection and ionic crosslinking.
Rayan A. M. Basodan, Jack Keddie, Byoungyoul Park, Hyun‐Joong Chung   +3 more
wiley   +1 more source

Spectroscopic limits of diamond anvils to 520 GPa and projected bandgap closure. [PDF]

Nat Commun
Hilberer A, Loubeyre P, Pépin C, Occelli F, Weck G, André R, Dumas P.   +6 more
europepmc   +1 more source

Removing Oxide Layers and Retaining Oxide‐Free Steel Surfaces by Polishing in Oxygen‐Free Atmosphere

Advanced Engineering Materials, EarlyView.
In this study, the efficacy of wet mechanical polishing under an oxygen‐free atmosphere for deoxidation and the retention of an oxide‐free steel surface are elucidated using X‐ray photoelectron spectroscopy. The methodology proved successful; however, the results were highly dependent on the preparation of the solvents used to clean the samples after ...
Friedrich Bürger, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +2 more
wiley   +1 more source

A contamination-free and low-leakage-current Cu-TSV technology enabled by engineered double-sided processing. [PDF]

Microsyst Nanoeng
Hao Y, Ding Y, Zhang Z, Yang B, Zhang J, Xie H, Chen Z.   +6 more
europepmc   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Metallization of 3D-Printed PET and PETG Samples with Different Filling Densities of the Inner Layers. [PDF]

Materials (Basel)
Petrova S, Lazarova D, Georgieva M, Petrova M, Dobrev D, Ditchev D.   +5 more
europepmc   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Bridging the Gap in Carbon Free Iron Making: How Hydrogen Affects the Reduction of Iron Ore between 900 and 1590 °C. [PDF]

ACS Sustain Chem Eng
Mohanta RK, Fisher D, Korobeinikov Y, Hong Q, Muhich C, Sridhar S, Leick N.   +6 more
europepmc   +1 more source