Results 91 to 100 of about 224,887 (344)

Versatile Green Transfer of Magnetoelectronics with Loss‐Free Performance and High Adhesion for Interactive Electronics

open access: yesAdvanced Functional Materials, EarlyView.
An environmentally friendly transfer printing method of nm‐thick giant magnetoresistive (GMR) sensors is demonstrated. This method, relying on water and biocompatible polyvinyl alcohol (PVA) polymer without the need of complex treatments, allows transferring thin films to a wide range of biological, organic, and inorganic substrates.
Olha Bezsmertna   +7 more
wiley   +1 more source

Cytotoxicity evaluation of methacrylate- and silorane-based composite resins

open access: yesCumhuriyet Dental Journal, 2012
Objectives: The objective of this study was to investigate and compare the cytotoxic effects of four composite resin materials with different content. Material and Methods: Two traditional methacrylate-based (Clearfil AP-X, RefleXions), as well as a self-
Digdem Eren   +3 more
doaj   +1 more source

Comparison between a silorane-based composite and methacrylate-based composites: shrinkage characteristics, thermal properties, gel point and vitrification point.

open access: yesDental materials journal, 2012
A silorane-based composite was compared against methacrylate-based composites in terms of shrinkage characteristics, thermal properties, gel point, and vitrification point. Shrinkage strain was measured using a laser triangulation method.
Bo-tao Gao   +4 more
semanticscholar   +1 more source

Vat Photopolymerization of High Molecular Weight Polymer Latexes with Pseudothermoplastic Properties for Recyclability

open access: yesAdvanced Functional Materials, EarlyView.
A photocurable latex system enables high‐resolution vat photopolymerization of water‐dispersed thermoplastics, yielding pseudothermoplastic materials with recyclability. The formulation permits precise control over mechanical properties and supports reprocessing through conventional and extrusion‐based methods. Compatibility with two‐photon 3D printing
Jon Ayestaran   +12 more
wiley   +1 more source

Wettability and thermal analysis of hydrophobic poly(methyl methacrylate)/silica nanocomposites

open access: yesAdsorption Science & Technology, 2017
Hydrophobic poly(methyl methacrylate)/silica layers on the glass support activated with plasma were obtained. Wettability was investigated from the contact angle measurements and surface free energy estimation by means of using contact angle hysteresis ...
Diana Rymuszka   +4 more
doaj   +1 more source

Ultrasoft Iontronics: Stretchable Diodes Enabled by Ionically Conductive Bottlebrush Elastomers

open access: yesAdvanced Functional Materials, EarlyView.
This work introduces a solvent‐free, ultrasoft, and stretchable ionic diode based on oppositely charged bottlebrush elastomers (BBEs). The BBE diode exhibits an ultralow Young's modulus (<23 kPa), a high rectification ratio of 46, and stretchability over 400%.
Xia Wu   +6 more
wiley   +1 more source

A Vertically‐Stacked Optoelectronic Sensor for Localized Hemodynamics Monitoring

open access: yesAdvanced Functional Materials, EarlyView.
This work introduces a hemodynamics monitoring sensor that features vertically stacked microLEDs and a heterogeneously integrated photodetector. The vertically stacked microLEDs enable localized measurements, and by designing the interoptode distance according to the depth of the target region, this vertically stacked optoelectronic sensor is ...
Taeyeon Lee   +9 more
wiley   +1 more source

Transforming Cellulose Into Functional Three‐Dimensional Structures

open access: yesAdvanced Functional Materials, EarlyView.
Cellulose is promising for replacing synthetic polymers due to its excellent mechanical properties and low cost. This review highlights the recent advancements in transforming cellulose into functional 3D structures, including liquid gels and porous materials.
Xia Sun   +5 more
wiley   +1 more source

Home - About - Disclaimer - Privacy