Results 271 to 280 of about 44,554 (315)

Trends in the Development of New Mg Alloys

Annual Review of Materials Research, 2008
Advanced Mg alloys require a stable microstructure that maintains good mechanical properties when exposed to high temperatures. On the basis of this demand, the search for new Mg alloys has stimulated the imagination of material scientists. This review's discussion ranges from modifications of commercial Mg-Al- and Mg-Zn-based alloys by Ca and rare ...
Bamberger, M., Dehm, G.
openaire   +2 more sources

Alloying behaviors of AgMg, AuMg and AgAl alloys

Journal of Physics and Chemistry of Solids, 1974
Abstract An expression of the structure-dependent energy of simple metal-noble metal binary alloy is given on the basis of the pseudopotential method. The energy is expressed as a sum of three parts; a band-structure energy, an electrostatic energy and a repulsive overlap energy, each of which is characterized by the usual long-range and short-range ...
openaire   +1 more source

Flammability of Mg–X Binary Alloys

Advanced Engineering Materials, 2012
AbstractFlammability of Mg–X alloys was studied for X = Al, Ca, Si, Sn, Sr, La, Mn, Zn, Zr, Ce, Gd, and Nd. One end of a horizontal cylindrical specimen was subjected to a free diffusion liquid petroleum gas (LPG) flame. There was no burning without some melting of the specimen tip.
Prasad, Arvind, Shi, Zhiming, Atrens, Andrej   +2 more
openaire   +3 more sources

Metallography of Mg Alloys

2019
Processing and composition determine microstructural properties. To reveal the microstructure, the metallographic investigation is a commonly used method, and therefore, it is a crucial part in the characterization of metals and alloys. Choosing incorrect preparation steps will lead to artefacts and misleading conclusions due to the compositional ...
Norbert Hort, Victor Floss, Sarkis Gavras, Gert Wiese, Domonkos Tolnai   +4 more
openaire   +1 more source

Thermochemical investigation of Sm–Mg alloys

Calphad, 2014
Abstract The paper focuses on the thermochemical behaviour of the binary Sm–Mg alloys. The enthalpies of formation of the Sm–Mg intermetallic compounds have been determined at 300 K by high temperature direct synthesis calorimetry. The following results in kJ/mole of atoms are reported: −18.5±2 (SmMg), −16.0±2 (SmMg 2 ), −12.0±2 (SmMg 3 ), −8.5±2 ...
DELSANTE, SIMONA, BORZONE, GABRIELLA
openaire   +1 more source

High Energy Micro-Arc Alloying of Mg-RE on AZ31 Mg Alloy

Advanced Materials Research, 2011
Mg-RE electrode was used for deposition of micro-arc coatings on AZ31 magnesium alloy upon variation in there different processing parameters(high, low and middle pulsed discharges). Mass transfer trends from electrode to substrate and microstructure of Mg-RE coating on AZ31 substrate were observed. Characterization has been performed by using scanning
Chang Jun Chen, Yan Zhan Su, Xing Xu, Min Zhang   +3 more
openaire   +1 more source

Biodegradable Mg and Mg alloys: Corrosion and biocompatibility

Materials Science and Engineering: B, 2011
Abstract This review discusses the current state and challenges in understanding Mg alloy corrosion behavior, in view of use of these materials for biodegradable implants. After the description of some basic and specific aspects of Mg alloy corrosion, the influence of specific biological environments on the corrosion behavior of Mg alloys is ...
openaire   +1 more source

Bonding of AZ91D Mg Alloy and Al Metal with Mg-Al Eutectic Alloy and its Application in Al Coating on AZ91D Mg Alloy

Materials Science Forum, 2009
AZ91D magnesium alloy and Al metal were bonded successfully at 450 oC with load of 25 or 31 MPa by using Mg-Al eutectic alloy as the solder in atmosphere. The microstructure of the AZ91D/Al joints was characterized by SEM equipped with EDS, and the bond strength was measured through three-point bending test.
X.R. Li, Wei Liang, Xing Guo Zhao, L.P. Bian   +3 more
openaire   +1 more source

Mechanical alloying and milling of Al–Mg alloys

Journal of Alloys and Compounds, 2009
Abstract Solid solubility extension of Mg in Al was achieved for the binary Al–Mg system in the range of 10–40 at.% Mg by mechanical alloying of elemental powder mixtures and by mechanical milling of pre-alloyed ingots. No indication for the formation of the equilibrium phases (β-Al3Mg2 and γ-Al12Mg17) after milling was observed.
S. Scudino, M. Sakaliyska, K.B. Surreddi, J. Eckert   +3 more
openaire   +1 more source

Amorphization of MgZn alloys by mechanical alloying

Materials Science and Engineering: A, 1989
Abstract We report for the first time on the synthesis of magnesium-based amorphous alloy powders using mechanical grinding. We synthesize an amorphous powder of the nominal composition Mg 70 Zn 30 . Using X-ray diffraction and differential scanning calorimetry (DSC) we analyse the details of the magnesium reaction as well as the crystallization ...
A. Calka, A.P. Radlinski
openaire   +1 more source