Results 111 to 120 of about 2,568,461 (274)
Analysis of Pressure and Velocity Variation in T-shaped Channel at Micron Level
Pakistan Journal of Engineering & Technology, 2020 Micro-electromechanical systems (MEMS) are microscopic devices based technology mainly involving the moving parts. Bio-MEM is a particular affiliate of MEMS technology in general. This paper studies and analyzes variations of pressure and velocity inside
Faiz Ul-Hassan +2 more
doaj
Plasmonic Micro-Channel Assisted Photonic Crystal Fiber Based Highly Sensitive Sensor for Multi-Analyte Detection. [PDF]
Nanomaterials (Basel), 2022 Kamrunnahar QM +7 more
europepmc +1 more source
Spin Dynamics in the van der Waals Ferromagnet CrTe2 Engineered by Niobium Doping
Advanced Functional Materials, EarlyView.Spin‐dynamic magnetic properties of van der Waals (vdW) ferromagnet 1T‐CrTe2 are tuned via niobium (Nb) as Cr1‐xNbxTe2 (x = 0–0.2). Nb doping enables wide‐band tuning of the resonance frequency from 40 GHz down to the few‐GHz regime, accompanied by a moderate increase in the Gilbert damping from ∼0.066 to ∼0.14.
Dhan Raj Lawati +16 more
wiley +1 more source
Advanced Functional Materials, EarlyView.A fully polymeric two‐dimensional array of Dielectric Elastomers enables self‐sensing, cooperative actuation, and large‐stroke operation in a DE‐based autonomous conveyor. Based only on voltage and current measurements at actuator level, the system detects the presence of a ball and subsequently drives it toward a target position.
Saverio Addario +6 more
wiley +1 more source
Entropy Generation Analysis of Peristaltic Flow of Nanomaterial in a Rotating Medium through Generalized Complaint Walls of Micro-Channel with Radiation and Heat Flux Effects. [PDF]
Micromachines (Basel), 2022 Ali A +5 more
europepmc +1 more source
Coordinated Architectural and Chemical Reinforcement in the Crushing Mandible of a Soldier Termite
Advanced Functional Materials, EarlyView.The crushing mandible of a soldier termite withstands substantial biting loads despite lacking mineral. Its cuticle is partitioned: convex teeth pair hardness and zinc enrichment with aligned chitin fibers for contact durability, while stiffer concave regions between teeth carry bending loads.
Andrew Tran Nguyen +16 more
wiley +1 more source
Boosting Conversion Efficiency in Zn3P2/InP Solar Cells Via Nanoscale Junction Engineering
Advanced Functional Materials, EarlyView.This study demonstrates the efficacy of selective area epitaxy (SAE) in enhancing the conversion efficiency of a Zn3P2${\rm Zn}_3{\rm P}_2$/InP heterojunction solar cell. The impact of the SAE pattern dimensions on the performance parameters is investigated. Small size opening limits Jsc because of current crowding whereas large size opening limits Voc
Raphael Lemerle +14 more
wiley +1 more source
Advanced Functional Materials, EarlyView.In this work, we use direct ink writing (DIW) to 3D print Bi2Te3‐based materials and naturally induce hierarchical functional nanostructures, which reduced the lattice thermal conductivity by half, resulting in high zT of 0.87and 0.89 in p‐type and n‐type compounds, respectively, competitive with commercial materials.
Liangwei Hu +12 more
wiley +1 more source
20107 Manufacture of Micro Channel and Gas Flow Visualization in Micro Channel
The Proceedings of Conference of Kanto Branch, 2006 Tsuyoshi ITAGAWA +2 more
openaire +2 more sources
Advanced Functional Materials, EarlyView.Polarity‐matched Zr–MOFs program Nafion's nanoscale morphology during solution casting. Hydrophilic UiO‐66 preserves hydrated pathways, while hydrophobic UiO‐67 increases the proton hopping sites by densifying ionic clusters. Combining both fillers yields a membrane that delivers 176 mS cm−1 conductivity, reaches 1.46 W cm−2 under 200 kPa, and triples ...
Yonghwi Cho +13 more
wiley +1 more source