Results 71 to 80 of about 6,032,982 (288)

Morphology, Transport, and Dynamics of Protein Adsorption in Open‐Cell Metal Foam

Advanced Engineering Materials, EarlyView.
Stainless steel (SS) open‐cell foams are shown to adsorb more protein per unit area than previously reported 316L SS and chromium oxide surfaces under static and flow conditions. An integrated approach combining 3D pore imaging, flow simulation, and protein adsorption experiments characterizes the foam’s performance.
Chinmaya Prerana Inguva, Joseph Lavoie, Afsaneh Rabiei   +2 more
wiley   +1 more source

Micro-Service Scheduling Model and Optimization for Protection and Control of Distribution Network Considering Virtualization Delay

Shanghai Jiaotong Daxue xuebao
The current research on distribution network terminals based on micro-service and container architecture overlooks the impact of virtualization delay in micro-service scheduling, restricting its application in scenarios with high real-time requirements ...
HU Kaiqiang, CAI Zexiang, CAI Yu, QU Jing, LIU Yuanyuan
doaj   +1 more source

Mobility-Induced Service Migration in Mobile Micro-clouds [PDF]

2014 IEEE Military Communications Conference, 2014
Mobile micro-cloud is an emerging technology in distributed computing, which is aimed at providing seamless computing/data access to the edge of the network when a centralized service may suffer from poor connectivity and long latency. Different from the traditional cloud, a mobile micro-cloud is smaller and deployed closer to users, typically attached
Shiqiang Wang 0001, Rahul Urgaonkar, Ting He 0001, Murtaza Zafer, Kevin S. Chan, Kin K. Leung   +5 more
openaire   +3 more sources

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source

A Study on Analyzing Travel Characteristics of Micro Electric Vehicles by Using GPS Data

Applied Sciences
A micro electric vehicle (micro-EV) is a small electric car with one or two seats designed for short-to-medium-distance trips. Micro-EVs produce relatively less pollution during operation and, due to their compact size, offer greater mobility in narrow ...
Sunhoon Kim, Sooncheon Hwang, Dongmin Lee   +2 more
doaj   +1 more source

The feminised service sector: from micro to macro analysis

Work Organisation, Labour and Globalisation, 2012
Research concerned with the relationship between gender and service work has typically relied on micro-level analyses, and privileged affective explanations of the feminised service sector.
Babs Grossman
doaj   +1 more source

Fully Printed High-Performance n-Type Metal Oxide Thin-Film Transistors Utilizing Coffee-Ring Effect

Nano-Micro Letters, 2021
Metal oxide thin-films transistors (TFTs) produced from solution-based printing techniques can lead to large-area electronics with low cost. However, the performance of current printed devices is inferior to those from vacuum-based methods due to poor ...
Kun Liang, Dingwei Li, Huihui Ren, Momo Zhao, Hong Wang, Mengfan Ding, Guangwei Xu, Xiaolong Zhao, Shibing Long, Siyuan Zhu, Pei Sheng, Wenbin Li, Xiao Lin, Bowen Zhu   +13 more
doaj   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source

TESTE DE UM FRAMEWORK PARA IMPLEMENTAÇÃO DA OPEN INNOVATION: ESTUDO DE CASO DE UMA EMPRESA DE AUTOMAÇÃO

Revista Brasileira de Gestão e Inovação, 2022
Para elevar a capacidade de inovação e competitividade, diferentes tipos e tamanhos de empresas têm adotado a estratégia Open Innovation – OI. Entretanto, a literatura demonstra que as empresas ainda enfrentam dificuldades e desafios para colocar em ...
Lindomar Subtil de Oliveira, Márcia Elisa Soares Echeveste, Marcelo Nogueira Cortimiglia, Elizandro Ferreira   +3 more
doaj  

Self‐Sintering Ionogel Binder for Flexible, Recyclable, and Healable Printed Giant Magnetoresistive Sensors

Advanced Functional Materials, EarlyView.
ABSTRACT Electronic waste has emerged as a major environmental challenge, driven by the massive consumption and a limited lifetime of modern electronic devices, stimulating the development of sustainable electronics. Here, an all‐biomaterial gelatin‐choline‐citric acid ([Ch][CA]) ionogel is developed as an active binder to realize self‐sintered ...
Lin Guo, Xiaotao Wang, Guannan Mu, Proloy Taran Das, Igor Veremchuk, Conrad Schubert, Aaron D. Cross, Yevhen Zabila, Xuan Peng, Larysa Baraban, Denys Makarov   +10 more
wiley   +1 more source