Results 131 to 140 of about 20,982 (319)

Compatibility of Methacrylate Based Resins Controls Interfacial Failure and Toughness in 3D‐Printed Multimaterial Composites

Advanced Engineering Materials, EarlyView.
This work shows that the mechanical performance of multimaterial digital light processing (DLP) printed thermoset composites is governed by resin compatibility and interfacial design rather than spatial patterning alone. Brittle and ductile resin combinations produced premature interfacial failure, while graded interfaces and mechanically compatible ...
Ahmed M. H. Ibrahim, Li Meng, Ahmad R. Najafi, Nicolas J. Alvarez   +3 more
wiley   +1 more source

Microstructure of Ceramic Nanocomposites

Materia Japan, 1998
Sekino, Tohru, Niihara, Koichi
openaire   +2 more sources

Microstructure and Optical Absorption Spectra of Transparent Glass-Ceramics Containing ZnAl2O4:Cr3+.

, 1993
Tsuguo Ishihara, Katsuhisa Tanaka, Kazuyuki Hirao, Naohiro Soga   +3 more
openalex   +2 more sources

Feasibility of Nitrogen as a Carrier Gas for Inconel Cold Spray in Hydropower Application

Advanced Engineering Materials, EarlyView.
N2, despite being nearly two orders of magnitude cheaper than He, is a feasible carrier gas for cold spray Inconel coatings in hydropower repair applications when higher gas temperature and pressure are used. Reducing powder size significantly improved cavitation resistance, while the addition of fine chromium carbide particles further enhanced erosion
Tianhao Wang, Mayur Pole, Tingkun Liu, Kenneth A. Ross, Christopher B. Smith   +4 more
wiley   +1 more source

Microstructure-Dependent Rotational Wear of Dental Glass-Ceramics Under Low Humidity. [PDF]

J Funct Biomater
Sánchez-González E, Rodríguez-Rojas F, Borrero-López O.   +2 more
europepmc   +1 more source

Effects of Al, B and C Additives on Microstructure and Mechanical Properties of Spark-Plasma-Sintered SiC Ceramics

, 2005
Kyeong‐Sik Cho, Kwang Soon Lee
openalex   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Study on the Influence of Microstructure on the Rolling Contact Fatigue Performance of Silicon Nitride Ceramics Balls. [PDF]

Materials (Basel)
Sun F, Jia D, Li B, Dong T, Shen C, Zhang Y, Wang Z, Zhang W.   +7 more
europepmc   +1 more source

Effect of Ta2O5 Doping on the Microstructure and Dielectric Properties of BaTiO3 Based Ceramics

, 2014
Adnan Mousharraf, Md. Fakhrul Islam
openalex   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source