Results 101 to 110 of about 8,308 (222)
Brazilian Journal of Oral Sciences, 2015 Aim: To evaluate the selective acid etching of enamel and dentin on microtensile bond strength (µTBS) of a self-adhesive resin cement. Methods: Forty-eight bovine teeth were selected and had the buccal surface ground to obtain a flat dentin (n=24) or ...
Lúcia Trazzi Prieto +4 more
doaj +1 more source
Clinical and Experimental Dental Research, Volume 11, Issue 5, October 2025.ABSTRACT Objective Through a scoping review, this study meticulously mapped and characterized these nanostructured clays used to release antibacterial active compounds from direct restorative dental materials. Material and Methods The systematic approach involved searches in the PubMed/MEDLINE, Lilacs, Web of Science, Scopus, ScienceDirect, and Embase ...
Bárbara Faria Sa de Barbosa +8 more
wiley +1 more source
Microtensile bond strengths of adhesively bonded polymer-based CAD/CAM materials to dentin
Dental Materials Journal, 2019 This in vitro study aimed to evaluate the effect of two different polymer-based CAD/CAM materials; resin-nano ceramic (Lava Ultimate [LVU]) and composite (CERASMART [CS]), their different surface pre-treatments, and use of different resin cements on the µTBS of adhesively bonded CAD/CAM onlays to dentin.
Nuray, Capa +3 more
openaire +3 more sources
Classification review of dental adhesive systems: from the IV generation to the universal type [PDF]
, 2017 Adhesive dentistry has undergone great progress in the last decades. In light of minimal-invasive dentistry, this new approach promotes a more conservative cavity design, which relies on the effectiveness of current enamel-dentine adhesives.
Migliau, Guido +5 more
core +1 more source
Revista de Odontologia da UNESPIntroduction Increased adhesive temperature has been reported to promote solvent evaporation, reduce viscosity, and improve monomeric permeation into dentin.
Marcos Paulo Marchiori CARVALHO +5 more
doaj +1 more source
ORAL & implantology, 2013 Aim of this work is the in vitro bond strength evaluation of three bonding agents comparing the results of two kinds of test, Microtensile Bond Strength Test and a Shear Bond Strength Test. Bond strength tests have been used to test both direct and indirect restorative techniques to investigate if methods could give different results.72 human third ...
Gallusi, G. +4 more
openaire +2 more sources
Prediction of service life of polymeric sealant compositions for fuel tanks in aerospace structures from measurements of viscoelastic properties Annual report [PDF]
Prediction of service life of polymeric sealers for fuel tanks from viscoelastic ...
Boni, K. A. +3 more
core +1 more source
Influence of Autoclave Sterilization of Human Teeth on Dentin Bonding [PDF]
Pesquisa Brasileira em Odontopediatria e Clínica Integrada, 2006 Objective: The aim of this study was evaluate the effect of sterilization of human teeth used in laboratorial studies on dentin bonding. Method: Twenty extracted human third molars are distributed in two groups, with or without sterilization, GA and GB ...
Paula JACQUES, Josimeri HEBLING
doaj
Post-etching cleaning and resin/ceramic bonding: microtensile bond strength and EDX analysis.
The journal of adhesive dentistry, 2010 The aim of this study was to evaluate the microtensile bond strength of a resin composite bonded to two heat-pressed ceramics after performing different post-etching cleaning techniques.Resin composite specimens were bonded to IPS Empress Esthetic (EE) and IPS Empress 2 (E2) heat-pressed ceramic disks after etching with 10% HF, surface cleaning ...
Renan, Belli +3 more
openaire +2 more sources
Journal of Dentistry, 2019 Statement of the Problem: Laser can influence bonding mechanism by increasing the penetration depth of adhesive in smear layer. The effect of 940 nm diode laser on microtensile bond strength of adhesive to dentin has not been investigated in previous ...
Shahin Kasraei +3 more
doaj