Results 91 to 100 of about 22,149 (184)
Pathological Studies in Uteruses by X-ray Microtomography
Brazilian Journal of Radiation SciencesX-ray computed microtomography (microCT) is an advanced technique for evaluating materials that uses the principle of X-ray attenuation to form high-resolution two- and three-dimensional images.
Larissa M. Gonçalves +4 more
doaj +1 more source
A microCT Study of Three-Dimensional Patterns of Biomineralization in Pig Molars
Frontiers in Physiology, 2018 Domestic pig molars provide an interesting system to study the biomineralization process. The large size, thick enamel and complex crown morphology make pig molars relatively similar to human molars.
Susanna S. Sova +5 more
doaj +1 more source
Lasers in Surgery and Medicine, Volume 58, Issue 8, Page 683-692, October 2026.ABSTRACT Objective To evaluate the effects of antimicrobial photodynamic therapy (aPDT), systemic pharmacological therapy, and their combination on irradiated mandibular post‐extraction bone repair relevant to osteoradionecrosis (ORN) development in a rat model. Methods Twenty‐six male Wistar rats were initially randomized into five experimental groups:
Larissa Lopes Fonseca +9 more
wiley +1 more source
Frontiers in Veterinary ScienceIntroductionEquine trigeminal-mediated headshaking is a painful neuropathic disorder comparable to trigeminal neuralgia in humans. The selective destruction of pain fibers within the trigeminal ganglion, called rhizotomy, is the surgical treatment of ...
Richard Becker +8 more
doaj +1 more source
Polymer Composites, Volume 47, Issue 18, Page 16425-16441, 20 September 2026.Schematic of PA6/functionalized graphene nanoplatelet compounding and filament extrusion to 3D printing, sandwich panel fabrication, and mechanical characterization. ABSTRACT This study examines the impact and compressive behavior of additively manufactured polyamide 6 (PA6) nanocomposite sandwich panels reinforced with amine‐functionalized graphene ...
Russo Swart +3 more
wiley +1 more source
Computed Tomography for Non-destructive Inspection of Hot Structures and TPS Components [PDF]
, 2009 Verifying the quality of a large TPS structure component’s material and therefore providing its flight readiness capability, belongs to one of the most challenging objectives for non-destructive evaluation techniques. Especially when different components
Ullmann, Thomas +6 more
core
Advanced Engineering Materials, Volume 28, Issue 17, 9 September 2026.This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome +6 more
wiley +1 more source
Analysis of ceramic composites by 3D microtomography
, 1992 In the first part we describe the use of 3D X-ray microtomography for the analysis of density distributions inside and between cold pressed green state whisker reinforced Si3N4 / Si3N4 bending test specimens. The differences between a changing content of
Lüthi, Thomas (author) +1 more
core +1 more source
, 2014 peer reviewedX-ray microtomography, through quantification of soil structure at the microscale, could greatly facilitate the current understanding of soil hydrodynamic behaviour.
Roisin, Christian +5 more
core +1 more source
, 1993 X-ray microtomography is used to nondestructively section printed wiring boards in which conductive anodic filaments (CAFs) had grown, Quantification of the spatial distribution of copper is compared for microtomography and for serial sections obtained ...
L. L. Dollar +7 more
core +1 more source