Results 31 to 40 of about 3,866,167 (193)
Kapal, 2017 Proses pengelasan yang di lakukan pada material aluminium 5083 yang banyak di gunakan pada industri perkapalan yang khususnya digunakan pada bagian konstruksi.
Muhammad Hafid Huda +2 more
doaj +1 more source
Comparison of Properties and Bead Geometry in MIG and CMT Single Layer Samples for WAAM Applications
Metals, 2021 The process of Wire Arc Additive Manufacturing (WAAM) utilizes arc welding technology to fabricate metallic components by depositing material in a selective layered fashion.
Harley Stinson +3 more
doaj +1 more source
Pemilihan Teknik Pengelasan Optimal antara MIG dan TIG Menggunakan Metode AHP
Journal of Industrial Engineering and Operation ManagementPenelitian ini bertujuan untuk menentukan teknik pengelasan yang optimal antara MIG (Metal Inert Gas) dan TIG (Tungsten Inert Gas) dalam proses produksi rangka bus di PT. Laksana Bus Manufaktur.
Muhammad Viky Fathurrohman, Antono Adhi
doaj +1 more source
Effect of Double Pulse MIG Welding on Porosity Formation on Aluminium 5083 Fillet Joint [PDF]
MATEC Web of Conferences, 2019 In this article, parameters of Double-Pulse Metal Inert Gas Welding (DP-MIG) was used for minimising a porosity formation in a T-joint fillet weld. AA5083-H112 aluminium alloy (Non-heat treatable series) with the plate thickness of 10 millimetres is base
Warinsiriruk Eakkachai +2 more
doaj +1 more source
International Journal of Recent Technology and Engineering (IJRTE), 2019 Development of dissimilar metal welds (DMW) presents itself as an important research domain with respect to the industrial requirements. The joints formed by dissimilar metals should have superior metallurgical properties and an ability to withstand severe operational conditions.
Rakesh Chaudhari, Asha Ingle
openaire +1 more source
STUDI KARAKTERISTIK LASAN ALUMUNIUM 6061-T6 DENGAN BERBAGAI METODE PENGELASAN
Scientific Journal of Mechanical Engineering KinematikaPenggunaan metode tungten inert gas (TIG) dan metal inert gas (MIG) telah banyak dipergunakan untuk logam, namun metode shielded metal arc welding (SMAW) sangat jarang digunakan pada alumunium. Studi ini bertujuan untuk melihat kualitas lasan menggunakan
Josua Simaremare, Suprianto Suprianto
doaj +1 more source
Small, EarlyView.Abrasion of few‐layer graphene (FLG)–epoxy composites generated respirable particles in which FLG remained fully embedded, as confirmed by correlative HR‑TEM, Raman, and ToF‑SIMS analyses. Advanced lung cell models revealed no cytotoxic or inflammatory responses, and only high‑dose epoxy particles reduced mucociliary clearance.
Govind Gupta +20 more
wiley +1 more source
Soldagem MIG/MAG em transferência metálica por curto-circuito controlado aplicada ao passe de raiz [PDF]
, 2005 Dissertação (mestrado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós Graduação em Engenharia Mecânica.O presente trabalho consiste no estudo e desenvolvimento do Processo de Soldagem MIG/MAG em Transferência Metálica por ...
Silva, Régis Henrique Gonçalves e
core
Online Detection of Keyhole Status in a Laser-MIG Hybrid Welding Process
Metals, 2022 During laser-metal inert gas (MIG) hybrid welding, a large amount of welding status information is generated in droplet transfer, keyhole and molten pool.
Xi’an Fan +3 more
doaj +1 more source
steel research international, EarlyView.Prebending of 304L/Q345R cladded plates significantly alters the subsequent weld thermal cycle and modifies the local interfacial microstructure. Combined electron backscatter diffraction (EBSD) and microscopy analysis demonstrates that deformation twinning, martensitic transformation, and defect initiation are concentrated at the trimaterial junction,
Ali Fahem +2 more
wiley +1 more source