Results 51 to 60 of about 3,090,742 (298)
IEEE Access, 2022 More connectivity, higher data rates, more reliability, massive network capacity, higher performance and fewer delays are required in the fifth generation (5G) of cellular networks.
Semah Mabrouki +3 more
doaj +1 more source
Advanced Engineering Materials, Volume 27, Issue 6, March 2025.ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur +5 more
wiley +1 more source
Review of 3D Printed Millimeter-Wave and Terahertz Passive Devices
International Journal of Antennas and Propagation, 2017 The 3D printing technology is catching attention nowadays. It has certain advantages over the traditional fabrication processes. We give a chronical review of the 3D printing technology from the time it was invented. This technology has also been used to
Bing Zhang +4 more
doaj +1 more source
Tunable triple-band millimeter-wave absorbing metasurface based on nematic liquid crystal
AIP Advances, 2022 We propose and design a tunable triple-band millimeter-wave absorbing metasurface based on nematic liquid crystal (NLC). Numerical results based on both effective circuit model and full-wave simulations verify the triple-band absorption property.
Qiang Wang +4 more
doaj +1 more source
Smart millimeter-wave devices using liquid crystal
, 2004 Smart liquid crystal (LC) millimeter-wave (MMW) electronic devices are demonstrated using the electrically-controllable permittivity through LC directors\u27 reorientation. In this paper, we review the LC classes and its important physical properties for
Haiying Wang +9 more
core +1 more source
Advanced Engineering Materials, EarlyView.A simplified thermoplastic pultrusion model is developed to predict thermal fields in glass fiber/polyethylene terephthalate (GF/PET) composites with reduced computational cost. By combining effective material homogenization, validation against literature data, and Gaussian‐process‐based optimization, the study reveals how heating limits, pulling speed,
Elder Soares +3 more
wiley +1 more source
Planar slow wave structures for millimeter-wave vacuum electron devices
, 2018 <p>Underlying data corresponding to the conference paper: G. Ulisse, V. Krozer, "Planar slow wave structures for millimeter-wave vacuum electron devices", 47th European Microwave Conference (EuMC), Nuremberg, Germany, October 2017 ...
Giacomo Ulisse (8229951) +3 more
core +1 more source
Adaptive Foam 3D Printing of Ultralight and Multifunctional Materials
Advanced Engineering Materials, EarlyView.Adaptive foam 3D printing, enabled by expandable microspheres, imparts cellular structures to thermoplastic and thermosetting polymers, manufactured through a variety of processes including fused filament fabrication, direct ink writing, digital light processing, and inkjet printing.
Nariman Rajabifar, Amir Ameli
wiley +1 more source
Advanced Engineering Materials, EarlyView.A thermoplastic PMMA‐based photoresin enables high‐resolution DLP printing followed by solvent‐vapor smoothing. The treatment reduces staircase‐induced surface roughness from 2.33 µm to 129 nm and increases visible‐light transmittance from approximately 30% to 80%, providing a route toward transparent PMMA components for rapid prototyping and non ...
Rozhin Heydarpour +5 more
wiley +1 more source
Advanced Functional Materials, EarlyView.Edible electronics needs integrated logic circuits for computation and control. This work presents a potentially edible printed chitosan‐gated transistor with a design optimized for integration in circuits. Its implementation in integrated logic gates and circuits operating at low voltage (0.7 V) is demonstrated, as well as the compatibility with an ...
Giulia Coco +8 more
wiley +1 more source