Results 241 to 250 of about 1,860,729 (283)

Dynamic milling force model for a milling cutter under vibration

The International Journal of Advanced Manufacturing Technology, 2020
Dynamic milling force under milling vibration is an important indicator for evaluating the milling stability of a milling cutter. The existing modeling methods for milling force ignore the milling vibration for the instantaneous milling behavior of a milling cutter and its teeth, the instantaneous cutter-workpiece engagement, and the milling force. The
Bin Jiang, Tingzheng Zhang, Peiyi Zhao, Junfeng Zhao   +3 more
openaire   +1 more source

Fuzzy cutting force modelling in micro-milling

Journal of Intelligent & Fuzzy Systems, 2013
Reliable prediction of cutting forces is essential for micromilling. In this paper, a fuzzy cutting force modelling method based on subtractive clustering method filters the noise and estimates the instantaneous cutting forces using observations acquired by sensors during cutting experiments.
Qun Ren, Luc Baron, Marek Balazinski, Krzysztof Jemielniak   +3 more
openaire   +2 more sources

Model-based Predictive Force Control in Milling

2019 18th European Control Conference (ECC), 2019
Milling is a manufacturing process for machining metals, where a milling tool cuts metal from a workpiece. Especially during rough milling the productivity is significantly affected by the process force that acts on the tool. The process force depends on the feed velocity and the engagement conditions.
Sebastian Stemmler, Muzaffer Ay, Max Schwenzer, Dirk Abel, Thomas Bergs   +4 more
openaire   +1 more source

Wordsworth, Mill, and the Force of Habit

The Wordsworth Circle, 2011
When the spirit of the young John Stuart Mill finally broke, it was reading Wordsworth that helped mend it; and the new thing that Wordsworth brought to Mill's life was chiefly the realisation that things could feel new. Mill's upbringing, as designed and implemented by his father, was an extraordinary experiment in moral philosophy--an extraordinarily
openaire   +1 more source

Power and Forces in Milling S.A.E. 3150 Steel With Helical Mills

Journal of Fluids Engineering, 1937
Abstract This paper outlines a series of tests conducted on a milling machine using slab mills of similar construction except for variation in rake angle, when milling an S.A.E. 3150 steel. The cutters had rake angles of 20, 15, 10, and 5 deg as variables, but otherwise were 3 in. in diameter, and had 12 teeth on a 25-deg left-hand helix.
O. W. Boston, W. W. Gilbert, K. B. Kaiser   +2 more
openaire   +1 more source

Feature Analysis for Milling Force of Three-Edge End Mills

Advanced Materials Research, 2010
In order to obtain the features of force for three-edge end mills in normally milling, an equation of milling force in Y direction was built based on the presumption that the forces of every edge are not equal, and its simulation waveforms in time domain was analyzed, the force of Y direction was found to present different spectral features under ...
Can Liu, Guang Yu Tan, G.H. Li, J.S. Liang, D.R. Li   +4 more
openaire   +1 more source

MEASURING MILLING FORCE WITH TWO C9C FORCE TRANSDUCERS

Conference proceedings : 60th Anniversary of the Association of Production Engineering of Serbia
Cutting forces during milling can be measured using several high-quality, though expensive, devices available on the market. In this study, an attempt was made to measure the cutting forces using two C9C force transducers. The results obtained from these measurements are discussed in this paper.
Attila RÉTFALVI, Tamás TORNAI
openaire   +1 more source

Force Prediction in Plunge Milling of Inconel 718

2012
In manufacturing, plunge milling is one of the most effective methods and widely used for material removal in rough and semi-rough machining while machining hard material. The cutting force in milling is very difficult and complex to predict, especially in plunge milling since there are many parameters acting as the design variables in the cutting ...
Kejia Zhuang, Xiaoming Zhang, Xiaojian Zhang, Han Ding 0001   +3 more
openaire   +2 more sources

The Mechanism of Surface Trajectories and Milling Forces in Micro-Milling Processing

Advanced Materials Research, 2012
In practical industrial processing, in order to make the tiny functional devices assembly accuracy as high as possible, which raises an very high requirement for surface quality of micro workpiece. Some of the important factors in controlling the surface quality with the level of the trajectories and forces of the blade across on the workpiece have a ...
Jin Feng Zhang, Ya Dong Dong, Yong Zhen Zhang, Jun Cheng   +3 more
openaire   +1 more source

Calculation of the Cutting Forces and Torque when Milling with End Mills

Proceedings of Higher Educational Institutions. Маchine Building, 2020
This paper presents a computational sequence for calculating the components of the cutting force and torque when milling with carbide end mills. The calculation algorithm includes the transition from the tangential and radial components of the force to the force components in the machine coordinate system.
openaire   +1 more source