Results 41 to 50 of about 429 (184)
EPJ Web of Conferences, 2017 This work discusses the mathematical model for laminar-flow heat transfer in a minichannel. The boundary conditions in the form of temperature distributions on the outer sides of the channel walls were determined from experimental data.
Maciejewska Beata +2 more
doaj +1 more source
Digital Flow Rate Measurement System Design for Minichannel based on Cross Correlation Technique [PDF]
Engineering and Technology Journal, 2017 In this paper, a demonstration for an experimental study to measure mean fluid velocity in minichannels is presented. Fluid flow velocity was estimated by applying cross correlation technique on measured thermal fluctuation using two ultra-small ...
H.A. Dhahad, E.M. Alfayydh, K.H. Fahem
doaj +1 more source
Environmental Progress &Sustainable Energy, Volume 45, Issue 4, July/August 2026.Abstract The Kigali Amendment's mandate to phase down high‐GWP refrigerants highlights the urgent need for sustainable alternatives in cold climate heat pumps, which are critical for delivering efficient heating in severely cold regions. This study evaluates ultralow‐GWP refrigerants—R‐290, R‐152a, R‐161, R‐1234yf, and R‐1234ze(E)—for application in a ...
Kuanrong Qiu, Martin Thomas
wiley +1 more source
Investigation of Two-Phase Flow in Short Horizontal Mini Channel Height of 1 MM
MATEC Web of Conferences, 2016 The experiments with two-phase flow in the short horizontal rectangular minichannel with the height of 1 mm and width of 29 mm have been carried out using water and gas nitrogen.
Ron’shin Fedor, Cheverda Vyacheslav
doaj +1 more source
Energies, 2020 Concentrator photovoltaics have several advantages over flat plate systems. However, the increase in solar concentration usually leads to an increase in the solar cell temperature, which decreases the performance of the system.
Asmaa Ahmed +3 more
doaj +1 more source
Asia-Pacific Journal of Chemical Engineering, Volume 21, Issue 2, March/April 2026.ABSTRACT The growing impacts of climate change and energy scarcity demand environmentally sustainable refrigeration solutions. This study investigates eco‐friendly refrigerants (R152a, R290 and R600a) and their optimized ternary mixture as alternatives to R134a. Four blend compositions were analysed using experimental testing and REFPROP 10.0 modelling
M. Periyasamy, P. Senthilkumar
wiley +1 more source
Shaping the Future of Energy: Breakthrough Additive Manufacturing (3D) Technologies for Renewables
International Journal of Energy Research, Volume 2026, Issue 1, 2026.Additive manufacturing (AM), a rapidly growing field of application, is widely used to create environmentally friendly energy production and storage systems. This study presents a comprehensive analysis of recent developments in the production of renewable energy systems (RESs) using AM technologies, focusing on advantages, challenges, and possible ...
Gülbahar Bilgiç Tüzemen +7 more
wiley +1 more source
EnergiesThis study presents a comprehensive experimental investigation into the frictional pressure drop of two-phase flows—boiling and condensation—in horizontal minichannels, emphasizing its impact on the energy efficiency of vapor compression systems. A total
Calos Martínez-Lara +2 more
doaj +1 more source
EPJ Web of Conferences, 2014 The paper presents results of heat transfer research on flow boiling in a rectangular minichannel positioned vertically, with an enhanced surface. One of the channel walls was made of thin foil powered by direct current. This foil is enhanced on the side
Hożejowska Sylwia, Piasecka Magdalena
doaj +1 more source
International Journal of Photoenergy, Volume 2026, Issue 1, 2026.PVM and PV/TM are currently common for greener energy generation, but the operating temperatures can greatly influence their performance. Hence, thermal management is crucial for improving performance and reliability. Our review details a detailed study on fin‐based cooling techniques utilised for PVM and PV/TM.
G. Anitha +3 more
wiley +1 more source