Results 71 to 80 of about 802 (259)

Numerical Simulation of Hydrodynamics and Heat Transfer in a Reactor with a Fluidized Bed of Catalyst Particles in a Three-Dimensional Formulation

Applied Sciences
The hydrodynamics and heat transfer in a reactor with a fluidized bed of catalyst particles and an inert material were simulated. The particle bed (the particle density was 2350 kg/m3, and the particle diameter was 1.5 to 4 mm) was located in a ...
Nikolai V. Ulitin, Konstantin A. Tereshchenko, Ilya S. Rodionov, Konstantin A. Alekseev, Daria A. Shiyan, Kharlampii E. Kharlampidi, Yaroslav O. Mezhuev   +6 more
doaj   +1 more source

Modular Critical Element Recycling Platform Using a Nanoporous Additively Manufactured Gyroid

Advanced Engineering Materials, EarlyView.
A modular recycling platform integrates 3D‐printed nanoporous gyroid structures to enable efficient critical element recovery. This system utilizes a hierarchical architecture, combining macroscopic channels with polymerization‐induced nanoscale porosity. By systematically tuning structural wall thickness and resin formulation, the platform achieves an
Xiangyu Gao, Keldy Mason, Mert Gülçür, Rachel Paddock‐Lamb, Prince Alvin Fofanah, Zachariah A. Page, Michael Cullinan   +6 more
wiley   +1 more source

The Impact of Particle Size in Fluidized Bed on Heat Transfer Behavior: A Review

Advances in Mechanical and Materials Engineering
This review paper explores the significance of fluidized bed heat exchangers in various industrial applications. By delving into the operation of fluidized beds as multiphase flow systems, the aim is to enhance their capabilities and efficiency.
Ahmed Hammood Darweesh, Musa Mustafa Weis   +1 more
doaj   +1 more source

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Superlubricity and Corrosion Inhibition Properties of Solvate Ionic Liquids in Hybrid Carbon Fiber Reinforced Plastic–Steel Interfaces

Advanced Engineering Materials, EarlyView.
Solvate ionic liquids lubrication reduced the coefficient of friction by ∼60% compared to dry sliding, reaching steady‐state values as low as 0.04–0.05. Corrosion weight‐loss measurements in 1 M HCl further demonstrated significant inhibition behavior, with only 100 ppm of [Li(G3)][TFSI] (∼68.5 μL/L) reducing corrosion‐product weight loss by 63 ...
Sameh Dabees, Timothy Harte, Bhagya Dharmasiri, Y. Athulya Wickramasingha, David J. Hayne, Daniel J. Eyckens, Luke C. Henderson   +6 more
wiley   +1 more source

Model‐Guided Design of Paper Membrane Architectures for Controlled Flow and Enhanced Diagnostic Sensitivity

Advanced Engineering Materials, EarlyView.
Geometrical modifications on nitrocellulose membranes can result in observable differences in signal intensity relative to a reference membrane (top and bottom left). Using two reference experiments, we have developed a theoretical model that can reproduce the experimentally observed flow changes and provide information on membrane parameters, e.g ...
Maria Dimaki, Lea Holritz, Winnie E. Svendsen   +2 more
wiley   +1 more source

Models for Minimum Liquid Fluidization Velocity of Gas-Liquid Fluidized Beds.

JOURNAL OF CHEMICAL ENGINEERING OF JAPAN, 2001
The gas-perturbed liquid model of Zhang et al. (1995) is modified in an effort to improve its prediction of the minimum liquid velocity of fluidization, Ulmf, of a bed of solid particles in the presence of a low or moderate cocurrent flow of gas. Variants of the model are considered where the buoyancy term is based on the gas-liquid mixture, instead of
lee d. h., n. epstein, j. r. grace
openaire   +1 more source

Stretching the Printability Metric in Direct‐Ink Writing with Highly Extensible Yield‐Stress Fluids

Advanced Functional Materials, EarlyView.
This study introduces “drawability” as a new metric for assessing printability in direct‐ink writing, focusing on gap‐spanning performance and speed robustness. By designing yield‐stress fluids with high extensibility, we demonstrate that extensional strain‐to‐break significantly enhances printability.
Chaimongkol Saengow, Samya Sen, Joaquin Yus, Eliza E. Lovrich, Amanda G. Hoika, Kelly M. Chang, Arielle A. Pfeil, Nellie Haug, Amy J. Wagoner Johnson, Randy H. Ewoldt   +9 more
wiley   +1 more source

Fluidization behavior of wood/sand mixtures

Maderas: Ciencia y Tecnología, 2014
In conversion of biomass to secondary energy carriers, several routes are possible, such as gasification, combustion and pyrolysis. In many of these processes it is necessary or advantageous to dry the biomass before further processing.
Bram J. Ramakers, Ronny de Ridder, Piet J.A.M. Kerkhof   +2 more
doaj  

Swelling‐Programmed Topographical Guidance for Dynamic Spheroid Self‐Assembly via a Mechanochemical Hydrogel Niche

Advanced Functional Materials, EarlyView.
A swelling‐programmed micropatterned hydrogel guides adherent cells through a controlled transition from cell–matrix anchoring to cadherin‐mediated cell–cell compaction, enabling rapid assembly of high‐viability spheroids with defined size and morphology.
Han Gyeol Nam, Seon Yeong Chae, Young Woo Kwon, Hye Jin Heo, Hye Rin Lee, Ji Hyeok Lee, Dong‐Wook Han, Yun Hak Kim, Suck Won Hong   +8 more
wiley   +1 more source