Results 71 to 80 of about 336,853 (296)

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

open access: yesAdvanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai   +2 more
wiley   +1 more source

5G mm-Wave Technology: Innovative Design of Integrating mm-Wave Wideband Antenna With a Compact CP Microwave Antenna for Diverse Applications

open access: yesIEEE Access
A compact dual-band antenna with a large frequency ratio and wideband mm-wave capabilities, incorporating multiple input multiple outputs (MIMO) technology, and designed for high isolation proposed for 5G applications.
Elagandula Aparna   +2 more
doaj   +1 more source

A Compact Spin‐Coated Graphene UWB Antenna for Breast Tumor Detection

open access: yesAdvanced Engineering Materials, EarlyView.
A compact, spin‐coated graphene ultra‐wideband patch antenna designed for breast tumor detection, capable of distinguishing between malignant and benign tumors. This innovative antenna can serve as an effective initial screening tool, particularly in resource‐limited settings such as rural areas, where access to advanced medical equipment like MRI and ...
Raja Rashidul Hasan   +9 more
wiley   +1 more source

Micromachined Millimetre-Wave Passive Components at 38 and 77 GHz [PDF]

open access: yes, 2009
A precision micro-fabrication technique has been developed for millimetre-wave components of air-filled three-dimensional structures, such as rectangular coaxial lines or waveguides.
Huang, F.   +4 more
core  

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

open access: yesAdvanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti   +11 more
wiley   +1 more source

Accelerating Deep Learning in Radar Systems: A Simulation Framework for 60 GHz Indoor Radar

open access: yesRemote Sensing
FMCW radar systems are increasingly used in diverse applications, and emerging technologies like JCAS offer new opportunities. However, machine learning for radar faces challenges due to limited application-specific datasets, often requiring advanced ...
Philipp Reitz   +4 more
doaj   +1 more source

Air‐Pressure–Actuated Vibroacoustic Metamaterial With Tunable Bandgap: Design, Modeling, and Characterization

open access: yesAdvanced Engineering Materials, EarlyView.
This article presents the design, modeling, and characterization of air‐pressure–actuated programmable vibroacoustic metamaterials (PVAMM). The study focuses on leveraging air pressure to dynamically tune resonance frequencies for effective noise attenuation.
William Kaal   +2 more
wiley   +1 more source

Resistance Rapid Heating of Aluminum Coatings in an Extreme High Vacuum–Adequate Atmosphere for Hot Stamping

open access: yesAdvanced Engineering Materials, EarlyView.
The subject of this work is the development of a corrosion‐protective coating on steel sheets for form hardening. Rapid heating in an extreme high vacuum (XHV)‐adequate atmosphere is a useful method to prevent oxidation during alloying of 22MnB5 and aluminum to obtain a metallurgical bonding.
Lorenz Albracht   +5 more
wiley   +1 more source

mm-Wave Waveguide Traveling-Wave Power Combiner Design Using an Equivalent Circuit Model

open access: yesIEEE Access, 2019
The waveguide traveling-wave power combiner (WTWPC) falls into the category of asymmetrical non-isolated power combiners, and, therefore, the active load modulation occurring within the combiner was investigated.
Honglei Sun   +3 more
doaj   +1 more source

Dielectric Barrier Discharge Plasma Deoxidation of Natively Oxide Layer of Copper Powders in a Fluidized Bed

open access: yesAdvanced Engineering Materials, EarlyView.
This paper presents a novel approach to reducing oxide layers on metal powders using low‐temperature hydrogen dielectric barrier discharge plasmas at atmospheric pressure. Unlike conventional hydrogen‐plasma reductions, the powders do not contact the plasma directly.
Shukang Zhang   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy