Results 131 to 140 of about 2,036,475 (297)

Wheelchair.q, a motorized wheelchair with stair climbing ability [PDF]

, 2011
Bozzini, Giuseppe Quaglia, Hartenberg, iBOT Mobility System, Magnani, Morales, Quaglia, Quaglia, Riccardo Oderio, TopChair SAS, Walter Franco   +10 more
core   +1 more source

The association of physical function with psychosocial patient‐reported outcomes in people with systemic lupus erythematosus

Arthritis Care &Research, Accepted Article.
Objective To evaluate how modifiable psychosocial factors and fatigue relate to physical functioning in patients with systemic lupus erythematosus (SLE). Methods In this cross‐sectional study of two demographically distinct cohorts [Approaches to Positive, Patient‐centered Experiences of Aging with Lupus (APPEAL) and California Lupus Epidemiology Study
Mrinalini Dey, Jessica Fitzpatrick, Maria Dall'Era, Charmayne Dunlop‐Thomas, Courtney Hoge, S. Sam Lim, Patricia P. Katz, Jinoos Yazdany, Laura C. Plantinga   +8 more
wiley   +1 more source

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Advanced Engineering Materials, EarlyView.
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer, Eric R. Hoglund, Anton V. Ievlev, Patrick E. Hopkins   +3 more
wiley   +1 more source

Experimental Evaluation of 100Cr6 Steel Microindented Surfaces Under Lubricated Nonconformal Point Contacts

Advanced Engineering Materials, EarlyView.
The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi, Pasquale Guglielmi, Gianfranco Palumbo, Giuseppe Carbone   +3 more
wiley   +1 more source

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Promoting accessibility for sustainable tourism: a spatial analysis of tourist attractions and public transportation networks in Bangkok

City, Territory and Architecture
The tourism sector plays a critical role in driving economic development. Within this domain, transportation systems are of paramount importance, facilitating connectivity between tourist attractions and shaping destination preferences. Consequently, the
Pawinee Iamtrakul, Sararad Chayphong, Ducksu Seo, Tu Anh Trinh   +3 more
doaj   +1 more source

Packaging of Macroscopic Material Payloads: Needs, Challenges, Concepts, and Future Directions

Advanced Engineering Materials, EarlyView.
This review introduces a unified framework that decomposes any macroscopic packaging system into the payload, packaging material, and packaging strategy and combines them into a conceptual packaging equation: packaging strategy = payload + packaging material.
Venkata S. R. Jampani, Manos Anyfantakis
wiley   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source