Results 221 to 230 of about 17,434 (315)

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

open access: yesAdvanced Engineering Materials, Volume 28, Issue 11, 3 June 2026.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek   +5 more
wiley   +1 more source

Nonlinear synchronization through vector subharmonic entrainment. [PDF]

open access: yesCommun Phys
Stoliarov D   +5 more
europepmc   +1 more source

Assembly of Cell‐Seeded 3D Printed Hydrogel Modules with Perfusable Channel Networks

open access: yesAdvanced Functional Materials, Volume 36, Issue 44, 1 June 2026.
Macroscale assembly was utilized to prepare perfusable tissue constructs from individually 3D printed hydrogel modules with embedded branched channel networks and port arrays for cell seeding. Novel multi‐material bioreactors were fabricated to facilitate the gluing of individual modules and the perfusion culture of assembled modular constructs seeded ...
Zachary J. Geffert   +10 more
wiley   +1 more source

O-band DWDM data transmission with quantum dot mode-locked comb laser and semiconductor optical amplifier. [PDF]

open access: yesSci Rep
Belykh VV   +7 more
europepmc   +1 more source

Cyclic Olefin Copolymers as Versatile Materials for Advanced Engineering Applications

open access: yesAdvanced Functional Materials, Volume 36, Issue 47, 11 June 2026.
Cyclic olefin copolymers (COCs) are presented as highly versatile materials combining tunable synthesis, excellent optical properties, and mechanical robustness. Their potential spans microfluidics, bioengineering, and advanced electronics, while emerging self‐healing and sustainable solutions highlight future opportunities.
Giulia Fredi   +3 more
wiley   +1 more source

Light‐Actuated Fiber‐Climbing Inchworm Robot Toward Endoluminal Navigation

open access: yesAdvanced Functional Materials, Volume 36, Issue 48, 15 June 2026.
A kirigami‐inspired soft inchworm robot harnesses optical energy from a customized side‐emitting optical fiber, guaranteeing its propulsion along the fiber body. The wavelength‐selective responsiveness of dye‐functionalized liquid crystal elastomers and the application of temporal illumination patterns enable sequential control of robot components. The
Antonio Lobosco   +6 more
wiley   +1 more source

Multicolor interband solitons in microcombs. [PDF]

open access: yesLight Sci Appl
Ji QX   +12 more
europepmc   +1 more source

3D Printing Innovations in Polymeric Porous and Patterned Architecture

open access: yesAdvanced Functional Materials, Volume 36, Issue 50, 22 June 2026.
Polymeric foams occupy a unique structural space between dense solids and open networks, where engineered void fraction governs mechanical compliance, thermal resistance, and mass transport. Additive manufacturing now enables precise spatial control over cellular architecture, unlocking designer foam structures across applications spanning crash ...
Dhanush Patil   +13 more
wiley   +1 more source

Cu-MOF as a saturable absorber for mode-locking at 2 µm and beyond. [PDF]

open access: yesSci Rep
Ahmad H   +9 more
europepmc   +1 more source

Soft Neural Interfaces for Circuit‐Level Analysis of Magnetogenetic Deep Brain Stimulation in Parkinson's Disease Models

open access: yesAdvanced Healthcare Materials, Volume 15, Issue 22, 12 June 2026.
ABSTRACT Magnetogenetic deep brain stimulation (MG‐DBS) represents a wireless neuromodulation that has demonstrated long‐lasting behavioral benefits in Parkinson's disease models. However, the circuit‐level mechanisms underlying these therapeutic effects have remained uncharacterized due to limitations of conventional neural interfaces.
Jakyoung Lee   +10 more
wiley   +1 more source

Home - About - Disclaimer - Privacy