Results 141 to 150 of about 3,111,671 (229)
Noise Suppression via Gain‐Dispersion‐Managed Nonlinear Amplification in a High‐Power Er‐Fiber Laser
Gain‐dispersion‐managed nonlinear pre‐amplification simultaneously suppresses phase and intensity noise, enabling scalable high‐power fiber amplification. The system delivers 102.3 W linearly polarized pulses with 1.19 µJ energy at 85.69 MHz and compresses them to 380 fs. Near‐linear power scaling without evident saturation highlights a practical route
Mei Yang +9 more
wiley +1 more source
A novel optical platform integrates a Sagnac‐based interferometer with a high‐brightness multiple‐plate continuum source to advance two‐dimensional electronic spectroscopy. The robust system delivers octave‐spanning, 3.7‐femtosecond pulses and achieves intrinsic attosecond‐level phase stability without active feedback.
Wei‐Chung Feng +5 more
wiley +1 more source
Micro‐transfer printing enables GaAs and InP gain materials to be integrated on a commercial silicon nitride photonic platform. The resulting chip supports O‐ and C‐band comb and single‐mode lasers, demonstrating a scalable route toward multi‐material, multi‐wavelength, and multifunctional integrated light sources.
Dongbo Wang +12 more
wiley +1 more source
First 20 Years of Orbitrap Mass Spectrometry as the Mainstream Analytical Technique
ABSTRACT This review traces the first 20 years of Orbitrap mass spectrometry as a mainstream high‑resolution and accurate‑mass (HR/AM) technology. It outlines the historical development of the Orbitrap analyzer, the evolution of major instrument families, and the key technological innovations that enabled its widespread adoption. Particular emphasis is
Alexander Makarov
wiley +1 more source
Research Progress of Passively Mode-Locked Fiber Lasers Based on Saturable Absorbers. [PDF]
Xie J, Liu T, Liu X, Wang F, Liu W.
europepmc +1 more source
Schematic overview of the investigated laminate architectures and reinforcement strategies used to evaluate their effects on the bearing performance and failure behaviour of thick carbon fibre/epoxy laminates. ABSTRACT This study provides a unified experimental comparison of 11 joint configurations in thick (7–12 mm) vacuum‐infused CFRP laminates ...
Hasan Caglar +7 more
wiley +1 more source
Thermal Aging and Tribological Tests of Additive Manufactured PLA Composites. ABSTRACT This study focuses on the additive manufacturing of pure polylactic acid (PLA) specimens and milled glass fiber (GF)‐filled PLA composites under thermal cycling aging and wear tests. Wear tracks have been analyzed via 3D optical profiling and SEM imaging.
Sinan Fidan +5 more
wiley +1 more source
Transient breathing dynamics during extinction of dissipative solitons in mode-locked fiber lasers. [PDF]
Yuan Z +9 more
europepmc +1 more source
Wear‐activated surface engineering of TPU/GNP nanocomposites through improved filler dispersion and interfacial anchoring of functionalized graphene nanoplatelets, leading to finer post‐abrasion textures and enhanced ice traction. ABSTRACT Graphene‐reinforced thermoplastic polyurethane (TPU) composites offer a promising route for developing ...
Sara Zahmatkesh +2 more
wiley +1 more source
Photovoltaic Effect in a III‐IV‐V Compound Semiconductor
A large reduction of the GaAs band gap is obtained with incorporation of 6.5% Ge during epitaxy without introducing extended defects or composition inhomogeneity. Heterojunction solar cell devices were fabricated with 0.76‐V open circuit voltage and an internal quantum efficiency above 40% at energies below the bandgap of the GaAs emitter.
José M. Ripalda +13 more
wiley +1 more source

