Results 211 to 220 of about 808,905 (255)

Maxwell II. Modes and Mode Propagation

2003
In the chapter on interference we discussed the resonance mode of a Fabry-Perot. We found that all light was transmitted for a specific wavelength λ and separation D of the Fabry-Perot plates. The condition for generation of the modes was D = mλ/2, where m was an integer.
openaire   +1 more source

Hydrogen Embrittlement in Mode II

British Corrosion Journal, 1982
AbstractAn arrangement for testing precracked material under Mode II loading is demonstrated, and it is shown that hydrogen embrittlement can occur in Mode II.
K. F. McGuinn, M. Aballe
openaire   +1 more source

Mode II delamination

2001
Publisher Summary This chapter elaborates the different aspects of the mode II delamination. Introducing shear loads into composite materials has presented major problems to the composite industry. Tests to determine shear moduli and strengths abound and all are open to criticism.
openaire   +1 more source

Stress Trajectories for Mode I and Mode II Cracks

International Journal of Fracture, 2006
Maximum shear stress trajectories are obtained for the mode I and for the mode II crack in an isotropic elastic solid in plane strain.
openaire   +1 more source

Addressing Modes II

1986
The 6502 and 65C02 have quite small instruction sets when compared with some of their fellow microprocessors—in fact the 6502 has a basic clique of just 56 instructions, while the 65C02 has only 8 more instructions, for a total of 64. However, many of these can be used in a variety of ways, which effectively increases the range of operations to 151 for
openaire   +1 more source

Fatigue/fracture characterization of composite bonded joints under mode I, mode II and mixed-mode I + II

Composite Structures, 2016
Abstract Experimental and numerical studies of the fatigue/fracture behavior of carbon–epoxy composite bonded joints under pure mode I, pure mode II and mixed-mode I + II loading were performed. The Double Cantilever Beam, End-Notched Flexure and Single-Leg Bending tests were used for fatigue/fracture characterization under high-cycle fatigue loading.
M.F.S.F. de Moura, J.P.M. Gonçalves, M.V. Fernandez   +2 more
openaire   +1 more source

Loading rate effects on mode I, mode II and mixed mode I-II delamination in advanced CFRP

2019
Delamination onset and propagation represent one of the most safety-critical failure modes in structures made of FRP laminates. Due to the widespread use of laminated composites in primary and secondary structures, the assessment of fracture behavior of FRP and the development of reliable analytical and numerical formulations for damage prediction are ...
openaire   +1 more source

Fatigue Delamination Growth in CFRP Composites: From Pure Mode I and Mode II to Mixed Mode I/II

Materials Science Forum, 2015
For composite design, it is desirable to have data covering the failure envelope from Mode I to Mode II. The existing standard procedures for quasi-static testing (ISO 15024 for Mode I and ISO DIS 15114 for Mode II) have recently been shown to be adaptable for the respective fatigue tests under displacement control.
Steffen Stelzer, Gerald Pinter
openaire   +1 more source

Avidin. II. Composition and mode of action of avidin A

Archives of Biochemistry and Biophysics, 1952
Abstract Avidin A is a glycoprotein containing mannose and hexosamine. Data concerning its amino acid composition and its amino, acidic, and basic groups are given. Avidin XA, while similar in most analytical respects, contains galactose also. A variety of chemical modification reactions did not appreciably affect the biotin-binding activity of ...
H, FRAENKEL-CONRAT, N S, SNELL, E D, DUCAY   +2 more
openaire   +2 more sources

Concepts for bridged Mode ii delamination cracks

Journal of the Mechanics and Physics of Solids, 1999
zbMATH Open Web Interface contents unavailable due to conflicting licenses.
MASSABO', ROBERTA, COX BN
openaire   +2 more sources