Results 91 to 100 of about 30,966 (260)

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Improving Mixed-Mode Fracture Properties of Concrete Reinforced with Macrosynthetic Plastic Fibers: An Experimental and Numerical Investigation

Buildings
This article offers a comprehensive analysis of the impact of MSPF on concrete’s mechanical properties and fracture behavior. Combining findings from numerical simulations and laboratory experiments, our study validates numerical models against diverse ...
Ali Permanoon, Majid Pouraminian, Nima Khorami, Sina GanjiMorad, Hojatallah Azarkhosh, Iman Sadrinejad, Somayyeh Pourbakhshian   +6 more
doaj   +1 more source

Experimental Evaluation of Mode II fracture Properties of Eucalyptus globulus L. [PDF]

Materials (Basel), 2020
Majano-Majano A, Lara-Bocanegra AJ, Xavier J, Morais J.   +3 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Continuous Stiffness Graded Metal–Ceramic Femoral Stems: UMAT‐Based Design and Finite Element Assessment

Advanced Engineering Materials, EarlyView.
Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley   +1 more source

Extrusion‐Based Additive Manufacturing of Advanced Ceramics: Strengthening Mechanisms and Process Optimization Review

Advanced Engineering Materials, EarlyView.
This review comprehensively evaluates extrusion‐based additive manufacturing for advanced ceramics, detailing feedstock options and key process parameters. By critically addressing defect mechanisms like porosity and cracking, the work highlights optimization strategies through machine learning and advanced postprocessing.
Meisam Bakhtiari, Mohammad Hadi Sheikh‐Ansari, Avinash Borgaonkar, Mehran Dadkhah, Abdollah Saboori   +4 more
wiley   +1 more source

Semantic Modeling in Materials Science and Engineering With Platform MaterialDigital Core Ontology 3.0

Advanced Engineering Materials, EarlyView.
The community‐driven Platform MaterialDigital Core Ontology (PMDco) 3.0 is introduced as a Basic Formal Ontology‐aligned semantic backbone for the processing–structure–properties paradigm in Materials Science and Engineering. Modular engineering, automated releases, and validation workflows are highlighted and key semantic patterns for materials ...
Markus Schilling, Philipp von Hartrott, Jörg Waitelonis, Thomas Hanke, Henk Birkholz, Hossein Beygi Nasrabadi, Khashayar Razghandi, Kamilla Zaripova, Felix Thonagel, Fabian Neuhaus, Martin Glauer, Lars Vogt, Harald Sack, Lutz Mädler, Bernd Bayerlein, Chris Eberl   +15 more
wiley   +1 more source

Enhancing Fatigue Crack Growth Resistance in Heterostructured Aluminum Bimetals by Tailored Interface Design

Advanced Engineering Materials, EarlyView.
Different Al/Al bimetals with a single engineered interface reveal how mechanical mismatch governs fatigue crack growth under cyclic loading. Additionally, loading–unloading–reloading tests link the microyielding behavior to the fatigue crack growth resistance, while crack‐path analysis reveals toughening mechanisms at the interface, highlighting ...
Sebastian Vollath, Philip Manuel Pohl, Heinz Werner Höppel   +2 more
wiley   +1 more source

Microstructure Modification of Additively Manufactured Mo–9Si–8B by Annealing and Its Effects on High‐Temperature Mechanical Properties

Advanced Engineering Materials, EarlyView.
Postbuild annealing systematically modifies the phase fractions and morphology of EB‐PBF processed Mo–9Si–8B. Quantitative microstructure–property correlations reveal how controlled phase evolution enhances high‐temperature compressive strength and creep resistance.
Christopher Schmidt, Yong Chen, Georg Hasemann, Benjamin Wahlmann, Carolin Körner, Manja Krüger   +5 more
wiley   +1 more source