Results 151 to 160 of about 225,848 (315)

The Impact of High‐Productivity Processing on the Fatigue Failure of an Additive Manufactured Superalloy HAYNES 282

Advanced Engineering Materials, EarlyView.
The low cycle fatigue life of additive manufactured HAYNES® 282® superalloy was investigated for conventional and high‐productivity processing: samples of the former lasted 1400–1700 cycles, while samples of the latter failed at ~ 1200 cycles, at 760 °C and 1% strain.
Abdul Shaafi Shaikh, Ahmed Fardan, Tatiana Mishurova, Eduard Hryha   +3 more
wiley   +1 more source

Comparative analysis of model compression techniques for achieving carbon efficient AI. [PDF]

Sci Rep
Paula E, Soni J, Upadhyay H, Lagos L.
europepmc   +1 more source

Facilitating Expedited Drug Approval– the Past, Present, and Future of Clinical Trials for Pediatric Rheumatic Disease

Arthritis Care &Research, Accepted Article.
Pamela F. Weiss, Hermine I. Brunner
wiley   +1 more source

Laser Powder Bed Fusion of Copper–Tungsten Composites for Heat Sink Applications in High‐Power Electronics

Advanced Engineering Materials, EarlyView.
This article demonstrates the successful qualification of a copper–tungsten composite for laser powder bed fusion. The resulting components exhibited high density, high thermal conductivity, and reduced thermal expansion. Heat sinks with complex geometries were successfully manufactured, clearly showcasing the material's potential for additive ...
Simon Rauh, Shashank Deepak Prabhu, Jannik Huber, Lioba Fischer, Gerhard Wolf, Nico Hempel, Peter Mayr   +6 more
wiley   +1 more source

Towards precision agriculture: metaheuristic model compression for enhanced pest recognition. [PDF]

Sci Rep
Parez S, Alghamdi NS, Mahmood T, Ullah W, Khan MA, Houda T, Dilshad N.   +6 more
europepmc   +1 more source

Autoregressive Models of Amplitude Modulations in Audio Compression

, 2009
Sriram Ganapathy, Petr Motlíček, Hynek Heřmanský   +2 more
openalex   +2 more sources

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

A survey of model compression techniques: past, present, and future. [PDF]

Front Robot AI
Liu D, Zhu Y, Liu Z, Liu Y, Han C, Tian J, Li R, Yi W.   +7 more
europepmc   +1 more source

Analysis of Molecular-level Conditions in Polymer Systems by Using a Pulse-Induced Dynamic Compression ATR Infrared Step Scan Time Resolved FT-IR. Part 1—Basic Simulation Study Based on a Fresnel Multiple Reflection Model—

, 2018
Yuji Nishikawa, Hiroto Itoh, Isao Noda, Takeshi Hasegawa   +3 more
openalex   +2 more sources

Numerical Investigation of Effect of Mechanical Compression on the Transport Properties of Fuel Cell Microporous Layer Using a Pore-Scale Model

, 2023
Heng Zhang, Hao Hu, Mrittunjoy Sarker, Xuanyu Shao, Zhigang Zhan, Pang‐Chieh Sui, Po‐Ya Abel Chuang   +6 more
openalex   +1 more source