Results 81 to 90 of about 173,303,186 (294)

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source

Cryogenic Deformation Behavior of TiAl and Insights Into Embrittlement After High‐Temperature Exposure Combined With Secondary Ion Mass Spectroscopy of Near Surface Chemistry

Advanced Engineering Materials, EarlyView.
Near‐surface deuterium enrichment profiles for different microstructural types of TiAl after exposure at 700 °C in a heavy water‐containing environment. The deuterium levels are significantly higher than expected from natural occurrence, indicating that the heavy water dissociated during the exposure treatment and entered the specimens.
Jonathan D. H. Paul, Alexander Welle, Dirk Matthiessen, Michael Oehring, Fritz Appel, Florian Pyczak   +5 more
wiley   +1 more source

On the Csorgo-Révész increments of finite dimensional Gaussian random fields [PDF]

In this paper, we establish some limit theorems on the combined Csorgo-Révész increments with moduli of continuity for finite dimensional Gaussian random fields under mild conditions, via estimating upper bounds of large deviation probabilities on ...
Kyo-Shin Hwang, Hwa-Sang Sung, Hee-Jin Moon, Yong-Kab Choi   +3 more
core  

Weaker forms of continuity [PDF]

, 1972
This paper is concerned with a study of various weaker forms of continuity. The definitions originated in [1], [2], and [4] . In Chapter I, the definitions of several types of continuity are given and examples are given to show that these are actually ...
Keith, Martha Allred, NC DOCKS at The University of North Carolina at Greensboro   +1 more
core  

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

Electrodeposition in Structural Lattices of Variable Architectures

Advanced Engineering Materials, EarlyView.
Electrodeposition enables geometry‐sensitive, autonomous void filling while simultaneously tuning chemical and mechanical properties. The development of approaches that can autonomously fill and heal material voids and yield composites with tailorable properties is increasingly relevant in engineering.
Yeong‐Man Kwon, Jingwen Zhang, Guido Musso, Alessandro F. Rotta Loria   +3 more
wiley   +1 more source

Thermal Cycle–Microstructure–Property Relationships in Rail Steel Heat‐Affected Zone Simulated by Gleeble

Advanced Engineering Materials, EarlyView.
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo, João Marcos da Silva Nunes, Marcelly Cristiny Nunes de Carvalho, Alex Rojas, Cristie Luis Kugelmeier, Cristhian Ricardo Loayza Loayza, João Carlos Ferreira, Maria Veronica Goncalves Rodrigues, Rute Sayuri Kano, Isaac Araújo Furtado, Jacyara Dalylla da Silva Nunes, Jhonatan Peres de Sousa, Marcos Natan da Silva Lima, Eden Santos Silva, Gedeon Silva Reis, Samuel Filgueiras Rodrigues   +15 more
wiley   +1 more source

Influence of Particle Shape and Size in Copper‐Based Low‐Temperature Metallization Paste for Solar Cells

Advanced Engineering Materials, EarlyView.
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi, M. N. Wengenmeyr, J. Bartsch, B. E. Rapp   +3 more
wiley   +1 more source