Results 81 to 90 of about 61,079 (261)
Advances in Materials Science and Engineering, 2014 Uniaxial compression test of cement asphalt (CA) mortar specimens, due to drying and wetting cycle of 0, 2, 4 and 8 times, is carried out by using the electronic universal test machine, with the strain rate ranging from 1 × 10−5 s−1 to 1 × 10−2 s−1.
Ping Wang +4 more
doaj +1 more source
Influence of coarse aggregate on concrete’s elasticity modulus
Acta Scientiarum: Technology, 2017 The modulus of elasticity of concrete is an important property because it is crucial for the control of deformation. The impossibility of obtaining concrete with higher elasticity modulus rates may cause economic liabilities due to the need for larger ...
Antônio Carlos dos Santos +4 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky +3 more
wiley +1 more source
Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method
Advanced Engineering Materials, EarlyView.A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley +1 more source
Advanced Engineering Materials, EarlyView.Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati +11 more
wiley +1 more source
The influence of water content on the longitudinal modulus of elasticity of maize stalk pith and rind tissues. [PDF]
Plant Methods, 2023 Sutherland B +3 more
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley +1 more source
Modulus of Elasticity of Concretes from Polish and Ukrainian Crushed Aggregates from Igneous Rocks
Budownictwo i Architektura, 2014 Test results concern modulus of elasticity and compressive strength of ordinary concretes made of various coarse aggregates from igneous rocks. Test results of some properties of these aggregates (3 crushed granites, 3 basalts, granodiorite, natural ...
Waldemar Budzyński +3 more
doaj +1 more source
New AI‐Assisted Approach for Expanding the Solution Space: Application to Lattice Structure Design
Advanced Engineering Materials, EarlyView.This work introduces an innovative framework for designing structured materials by ex panding the design space through reparameterization of qualitative variables into continuous structural descriptors. Combined with machine‐learning‐based prediction and multi‐objective optimization, the approach enables the discovery of novel lattice architectures ...
G. H. Gahimbare +5 more
wiley +1 more source
Modulus of Elasticity and Flexural Behavior of Glulam Beams Reinforced with Steel Mesh in Different Mesh Openings. [PDF]
Materials (Basel), 2023 Ulaşan H +4 more
europepmc +1 more source