Results 51 to 60 of about 40,950 (298)
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Moisture content modelling of thermal properties of persimmon (cv. 'Kaki')
Research in Agricultural Engineering, 2017 Persimmon is one of the tasty and sweet fruits with short shelf life. Thermal conductivity, thermal diffusivity and specific heat are necessary for storage, drying, packaging and designing of distillation machines.
Somaye Akbari, Reza Amiri Chayjan
doaj +1 more source
Modelling the cooking process of a single cereal grain [PDF]
, 1996 Four models are developed to assist with the uniform and accurate cooking of whole grains for Uncle Tobys breakfast cereals. 1. Heat satisfies a linear conduction equation and is found to rapidly penetrate the grain. 2.
McGowan, P., McGuiness, M.
core
The impact of compaction, moisture content, particle size and type of bulking agent on initial physical properties of sludge-bulking agent mixtures before composting [PDF]
, 2012 This study aimed to experimentally acquire evolution profiles between depth, bulk density, Free Air Space (FAS), air permeability and thermal conductivity in initial composting materials.
Benoist, Jean-Claude +4 more
core +4 more sources
Advanced Engineering Materials, EarlyView.This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira +4 more
wiley +1 more source
An Experimental Investigation of the Scaling of Columnar Joints [PDF]
, 2006 Columnar jointing is a fracture pattern common in igneous rocks in which cracks self-organize into a roughly hexagonal arrangement, leaving behind an ordered colonnade. We report observations of columnar jointing in a laboratory analog system, desiccated
A. H. Lachenbruch +13 more
core +2 more sources
Advanced Engineering Materials, EarlyView.This study examines how several molten high‐silicon electrical steels interact with both conventional and recycled MgO–C refractories. For this, various immersion experiments are conducted. In addition to infiltration, a number of mechanisms are identified and explained that control the corrosion of the refractory material.
Lukas Neubert +7 more
wiley +1 more source
Study on Effective Diffusivity of Sea Cucumbers with Heat Pump Drying
Zhileng xuebao, 2018 The effective diffusivity is an important parameter for mass transfer research on the drying of sea cucumbers. The dependence of the effective diffusivity on temperature has been adopted in current studies, while the effects of moisture content and ...
Zhao Haibo +4 more
doaj
Processibility of corn protein blends and resulting properties of the extrudates [PDF]
, 2012 During the last decade, the global biofuels industry has experienced exponential growth. By-products such as high protein corn gluten meal (CGM) and high fibre distillers dried grains with solubles (DDGS) have grown in parallel.
Rosentrater, Kurt A. +1 more
core +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source