Results 311 to 320 of about 357,395 (371)

Impedance Control Architecture for Robotic-Assisted Mold Polishing Based on Human Demonstration

IEEE transactions on industrial electronics (1982. Print), 2022
This article presents a computed-torque impedance control architecture for robotic-assisted mold polishing based on human skills.The mold polishing process for plastic injection is critical since tiny surface imperfections are easily visible in the ...
Hélio Ochoa, R. Cortesão
semanticscholar   +1 more source

Tailored and Highly Stretchable Sensor Prepared by Crosslinking an Enhanced 3D Printed UV‐Curable Sacrificial Mold

Advanced Functional Materials, 2020
Taking advantage of unlimited geometry design, 3D printed sacrificial mold cast with highly conductive polymer composites is used to prepare a sensor with designed structures.
Shuqiang Peng, Zian Wang, J. Lin, J. Miao, Longhui Zheng, Zhi Yang, Zixiang Weng, Lixin Wu   +7 more
semanticscholar   +1 more source

Traumatic arthritis of the hip after dislocation and acetabular fractures: treatment by mold arthroplasty. An end-result study using a new method of result evaluation.

Journal of Bone and Joint Surgery. American volume, 1969
An end-result analysis is presented of thirty-nine mold arthroplasties performed at the Massachusetts General Hospital between 1945 and 1965 in thirty-eight consecutive private patients for arthritis of the hip following fractures of the acetabulum or ...
W. Harris
semanticscholar   +1 more source

MOLDS IN ONYCHOMYCOSIS

International Journal of Dermatology, 1993
Abstract Background. Onychomycosis is a major cause of nail dystrophy. The causative organisms in onychomycosis are dermatophytes, Candida and molds. A variety of molds have been isolated from nails. Methods: Nail scrapings and clippings were collected from 100 cases and inoculated on slants containing SDA with cycloheximide 0.5 mg/mL, chloramphenicol ...
T. Girija Ratna Kumari, A Ramani, P. G. Shivananda, C. R. Srinivas, Rama Ramani   +4 more
openaire   +2 more sources

Non-destructive detection for mold colonies in rice based on hyperspectra and GWO-SVR.

The Journal of the Science of Food and Agriculture, 2018
BACKGROUND Mold contamination of grains not only contributes to inedible food, resulting in economic losses, but also leads to mold in humans and livestock, and can even be carcinogenic to them.
Cong Sunli, Sun Jun, Hanping Mao, Xiaohong Wu, Wang Pei, Xiaodong Zhang   +5 more
semanticscholar   +1 more source

CKshare: secured cloud-based knowledge-sharing blockchain for injection mold redesign

Enterprise Information Systems, 2018
This paper proposes a trustable mold redesign knowledge-sharing platform, known as CKshare, based on private cloud and blockchain technology. Firstly, we use private cloud to store the mold redesign knowledge of each party to meet its own privacy and ...
Zhi Li, Xinlai Liu, W. Wang, A. V. Barenji, G. Huang   +4 more
semanticscholar   +1 more source

Optical cross-talk reduction in a quantum-dot-based full-color micro-light-emitting-diode display by a lithographic-fabricated photoresist mold

, 2017
In this study, a full-color emission red–green–blue (RGB) quantum-dot (QD)-based micro-light-emitting-diode (micro-LED) array with the reduced optical cross-talk effect by a photoresist mold has been demonstrated.
Huang-Yu Lin, C. Sher, D. Hsieh, Xin-Yin Chen, Huang-Ming P. Chen, Teng-Ming Chen, K. Lau, Chyong-Hua Chen, C. Lin, H. Kuo   +9 more
semanticscholar   +1 more source

Update on Airborne Mold and Mold Allergy

Allergy and Asthma Proceedings, 1999
In considering the clinical aspects of fungal sensitivity, assessing exposure potential and clinical testing are essential. Valid prevalence data are difficult to secure. For ambient air, the Burkard Volumetric Spore Traps, or equal, capture spores best.
openaire   +3 more sources

Selective laser melting of maraging steel: mechanical properties development and its application in mold

, 2018
Purpose This paper aims to verify whether selective laser melting (SLM) could be used for manufacturing mold with conformal cooling channels and determine whether the mechanical properties development of SLM manufacturing maraging steel mold ...
Yuchao Bai, Yong-qiang Yang, Zefeng Xiao, Di Wang   +3 more
semanticscholar   +1 more source

Corrosion of Molds in Injection Molding Machines

Russian Engineering Research, 2018
The high corrosion rates of molds in injection molding machines are analyzed. The causes of such corrosion are considered.
S. A. Sorokina, A. D. Romanov
openaire   +2 more sources