Results 111 to 120 of about 223,547 (314)
Molding procedure for casting a variety of alloys [PDF]
, 1970 General procedure and molding sand composition for preparing molds usable for casting variety of alloys are developed. Molds are prepared from mixture of sand, sodium silicate binder, and organic liquid ester.
Fontes, M. J. +2 more
core +1 more source
Advanced Engineering Materials, EarlyView.A carbon‐free, as‐sintered MgO–steel cermet anode, fabricated via cold isostatic pressing using MgO–C refractory recyclate, was evaluated under laboratory‐scale K‐cryolite electrolysis at 800°C. Operation at this reduced temperature, combined with the electrolyte's limited electrical conductivity, led to an increase in cell voltage.
Farhan Hossain +7 more
wiley +1 more source
Development of an impact- and solvent-resistant thermoplastic composite matrix, phase 3 [PDF]
The polyimide from BTDA 1,6-hexanediamine and m-phenylenediamine was selected from a prior study for the present study. Methods to prepare prepreg which would provide low void composites at low molding pressures from the thermoplastic polyimide were ...
Delano, C. B., Kiskiras, C. J.
core +1 more source
Inverse Design Based on Nonlinear Thermoelastic Material Models Applied to Injection Molding
, 2019 This paper describes an inverse shape design method for thermoelastic bodies. With a known equilibrium shape as input, the focus of this paper is the determination of the corresponding initial shape of a body undergoing thermal expansion or contraction ...
Elgeti, Stefanie, Zwicke, Florian
core +1 more source
Towards Defect Phase Diagrams: From Research Data Management to Automated Workflows
Advanced Engineering Materials, EarlyView.A research data management infrastructure is presented for the systematic integration of heterogeneous experimental and simulation data required for defect phase diagrams. The approach combines openBIS with a companion application for large‐object storage, automated metadata extraction, provenance tracking and federated data access, thereby supporting ...
Khalil Rejiba +5 more
wiley +1 more source
Interaction of Ladle Slag With Varying SiO2 Content and Recyclate‐Based MgO–C Refractories
Advanced Engineering Materials, EarlyView.Ladle slags (CaO/Al2O3 = 1) with 1–20 wt% SiO2 were investigated in contact with industrial MgO–C refractories fabricated from fresh magnesia and 50 wt% recyclate. The sessile drop method at 1600°C reveals intensive gas formation, delayed slag infiltration in recyclate‐based samples, and, under high‐SiO2 slag, formation of a dense MgAl2O4‐rich ...
Anton Yehorov +6 more
wiley +1 more source
Flow behavior in liquid molding [PDF]
The liquid molding (LM) process for manufacturing polymer composites with structural properties has the potential to significantly lower fabrication costs and increase production rates.
Hunston, D., Parnas, R., Phelan, F.
core +1 more source
Molded composite pyrogen igniter for rocket motors [PDF]
, 1978 A lightweight pyrogen igniter assembly including an elongated molded plastic tube adapted to contain a pyrogen charge was designed for insertion into a rocket motor casing for ignition of the rocket motor charge. A molded plastic closure cap provided for
Heier, W. C., Lucy, M. H.
core +1 more source
Development of plasmonic sensor using gold nanobipyramids for detection of glyphosate based pesticide [PDF]
, 2020 The development of plasmonic sensor using gold nanobipyramids (GNBPs) as sensing material for detection of glyphosate based pesticide (GBP) has been performed. The GNBPs was synthesised using seed-mediated growth method (SMGM).
Nafisah, Suratun
core
Advanced Engineering Materials, EarlyView.Collagen hydrolysate is evaluated as a sustainable binder for MgO‐C refractories. Its thermally induced cross‐linking and gas release lead to expansion and cracking in large bricks, but tailored batches with lignin, recyclates, or fine graphite improve the gas release while thermal treatment and stability.
Till M. J. Stadtmüller +8 more
wiley +1 more source