Results 51 to 60 of about 223,547 (314)
Advanced Engineering Materials, EarlyView.Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The tribological behavior of 100Cr6 steel spheres textured via Vickers microindentation is evaluated under lubricated sliding by varying both dimple size and density. Fine and dense textures significantly reduce friction across all lubrication regimes, while large dimples increase it.
Farideh Davoodi +3 more
wiley +1 more source
Transfer molding of PMR-15 polyimide resin [PDF]
, 1985 Transfer molding is an economically viable method of producing small shapes of PMR-15 polyimide. It is shown that with regard to flexural, compressive, and tribological properties transfer-molded PMR-15 polyimide is essentially equivalent to PMR-15 ...
Moyer, D. W. +2 more
core +1 more source
Analysis of anisotropic bonded NdFeB Halbach cylinders accounting for partial powder alignment [PDF]
, 2000 An analytical technique is developed for predicting the performance of a bonded Halbach oriented anisotropic magnet, with due account of partial alignment of the NdFeB powder during injection molding.
Atallah, K. +4 more
core +1 more source
Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials
Advanced Engineering Materials, EarlyView.Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai +2 more
wiley +1 more source
MachinesIn this paper, the characteristics of special stamping process requirements and the shortcomings of existing application technology are studied. Through repeated motion simulation analysis and size optimization calculation, a kind of inertia-controlled ...
Yanzhong He, Xiang Luo, Xingsong Wang
doaj +1 more source
RESEARCH OF Al – SiC AND Cu – SiC SYSTEMS AFTER FORMING OF POWDER MIXTURE
Физико-химические аспекты изучения кластеров, наноструктур и наноматериалов, 2019 This article presents the results of a study of the microstructure and density of powder materials of the Al – SiC and Cu – SiC systems. They are obtained by cold forming a mixture of powders of copper, aluminum and silicon carbide.
A.N. Bashkaykina +2 more
doaj +1 more source
Processibility of black garbage bag as a novel binder system in metal injection molding [PDF]
, 2012 The issues to be highlighted here is to fundamentally evaluate the potential of using waste Garbage Bag from High Density Polyethylene (HDPE) as a backbone binder in Metal Injection Molding (MIM.) This is by the fact that the earth has tons of ...
Mustafa, Najwa
core
Advanced Engineering Materials, EarlyView.The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin +2 more
wiley +1 more source
Italy as the Kremlin’s ‘Trojan Horse’ in Europe: Some Overlooked Factors [PDF]
, 2020 As Russian influence in Italy grows, Putin’s ‘Trojan horse’ in the EU reflects several societal trends, molding perceptions of a foreign policy appropriate for ...
Patalakh, Artem
core