Results 181 to 190 of about 394 (223)

Development of Paint-Less Black Gloss Decorative Technology for Frame Molding

SAE Technical Paper Series, 2016
Shingo Hanano, Kanehiro Nagata, Yusuke Murase   +2 more
openalex   +3 more sources

A novel bionic dual-layer decorative membrane approach for suppressing interfacial defects in combined in-mold decoration and microcellular injection molding

Colloids and Surfaces A: Physicochemical and Engineering Aspects
Shengrui Yu, Tianyu Zhang, Lei Xu, Haitao Hua, Linan He, Senzhen Song, Fei Chen, Han Wen, Lanyu Zeng, Qingzhou Li, Huamin Zhou   +10 more
openalex   +2 more sources

Some of the next articles are maybe not open access.

Related searches:

Effect of decoration film on mold surface temperature during in-mold decoration injection molding process

International Communications in Heat and Mass Transfer, 2010
Abstract In-mold decoration (IMD) during injection molding is a relatively new injection molding technique and has been employed for plastic products to improve surface quality and achieving colorful surface design, etc. During IMD processing, the film is preformed as the shape of mold cavity and attached to one side of the mold wall (usually cavity ...
Hai-Mei Li, Shih-Tsun Huang, Shia-Chung Chen, Yi-Chao Wang   +3 more
openaire   +2 more sources

Yield improvement on in-mold decoration manufacturing through parameter optimization [PDF]

International Journal of Precision Engineering and Manufacturing, 2013
In-Mold Decoration (IMD) is an efficient, durable and cost effective technique for printing, painting, and forming plastic decorations. However, a large number of parameters involved in IMD manufacturing process and the complex relationship between these parameters make the determination of the optimal parameter setting a challenging task.
Liam Y. Hsieh, Kuo-Hao Chang
openaire   +1 more source

Factors Influencing the Warpage in In-Mold Decoration Injection Molded Composites

International Polymer Processing, 2013
Abstract This report studied, both experimentally and numerically, the factors affecting the warpage in in-mold decoration (IMD) injection molded parts. All experiments were conducted on an 80-ton injection-molding machine. The materials used in the experiments included poly(ethylene terephthalate) (PET) films and 30 % glass fiber-filled
D. Lee, W.-A. Chen, T.-W. Huang, Shih-Jung Liu   +3 more
openaire   +2 more sources

Electron Beam Curing of Hard Coating Resin for In-mold Decoration Foils [PDF]

Polymer Korea, 2011
The electron beam (EB) induced curing of a typical resin designed for the hard coating layer of in-mold decoration foils was investigated. The samples were irradiated with different doses of EB and the curing reaction was monitored by Fourier transform infrared (FTIR) spectroscopy.
Kwang Hee Lee, Geon Seok Kim, Byung Cheol Lee, Hyun Seog Sim, Deok Woo Yun   +4 more
openaire   +1 more source

Parameters Affecting the Ink Wash-off in In-mold Decoration of Injection Molded Parts

International Polymer Processing, 2012
Abstract Ink wash-off has been one of the problems that has confounded the overall success of the in-mold decoration (IMD) process for injection molded parts. In this report, an experimental matrix design based on the Taguchi method was conducted to examine the influence of processing parameters on the ink washoff of molded parts.
P.-W. Chang, Ching-Wei Hsu, Shih-Jung Liu   +2 more
openaire   +2 more sources

Study on the thermoforming of PC films used for in-mold decoration

International Communications in Heat and Mass Transfer, 2008
Abstract Preparation of thermoformed film is one of the critical steps for successful application of in-mold decoration (IMD) to parts of a complex shape. In the present study, a grid was printed on the surface of two PC films, 0.125 mm and 0.2 mm thick, and then the films were thermoformed into a cup shape by a drawing die under various process ...
Shia-Chung Chen, Rean-Der Chien, Rean-Der Chien, Ming-Chung Lin, Ming-Chung Lin, Shih-Tsun Huang   +5 more
openaire   +2 more sources

Molded acoustic and decorative mats and methods for forming the same

The Journal of the Acoustical Society of America, 2002
A multi-layer acoustically absorptive mat includes a base layer (130) having an exposure hole (140) defined therein. A face layer (110) is disposed adjacent the base layer. An acoustic absorbing layer is interposed between the base layer and the face layer.
Maureen R. Putt, David M Muckley, Steven G. Sehmer, Michael C. Jezewski, Milton D Lenarz   +4 more
openaire   +2 more sources

Mechanism of Bubble Formation in a Combined In-Mold Decoration and Microcellular Foaming Injection Molding Process

Fibers and Polymers, 2019
A combined in-mold decoration and microcellular foaming injection molding process (IMD/Mucell) is proposed to improve the surface quality of foamed parts. Through theoretical inference, the mathematical models of temperature field, velocity profile and forces on bubble were established with combining traditional mathematical models and the different ...
Bo He, Zhenghua Meng, Lin Hua, Wei Guo, Zhang Mengying, Huajie Mao   +5 more
openaire   +2 more sources