Results 161 to 170 of about 370 (245)

Hierarchical Multi‐Material Architectures With Gradient Design for Dynamic‐Range Flexible Tactile Sensing

open access: yesAdvanced Materials Technologies, EarlyView.
Hierarchical multi‐material TPMS lattices are engineered as flexible tactile sensors by combining soft and stiff elastomeric layers with a conformal conductive coating. The bilayer architecture delivers sensitivity at low pressures while maintaining a broad detectable range under large loads, enabling reliable pressure and vibration monitoring for ...
Reza Noroozi   +3 more
wiley   +1 more source

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

open access: yesAdvanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang   +9 more
wiley   +1 more source

Caballero-Engel meet Lasry-Lions: A uniqueness result. [PDF]

open access: yesMath Financ Econ
Alvarez F, Lippi F, Souganidis P.
europepmc   +1 more source

3D‐Printed Dual‐Doped Ag2Se‐Based Thermoelectric Films With Enhanced Thermal Stability

open access: yesAdvanced Materials Technologies, EarlyView.
Sb–Se dual doping enhances the thermal stability of Ag2Se‐based thermoelectric systems. The compositionally tuned nano‐ink is printed into flexible films by direct ink writing (DIW), retaining improved thermoelectric properties after annealing up to 400°C.
Ahasun Habib Hridoy   +8 more
wiley   +1 more source

Programmable Variable‐Stiffness Multilayer Elastomer Composites With High‐Aspect‐Ratio Low‐Melting‐Point Alloy Inclusions

open access: yesAdvanced Materials Technologies, EarlyView.
High‐aspect‐ratio low‐melting‐point alloy inclusions are embedded within multilayer silicone laminates to create thermally programmable stiffness. Sequential activation of alloy‐rich layers produces four distinct mechanical states and reconfigures tendon‐driven actuator trajectories under the same load.
Palpolage Don Shehan Hiroshan Gunawardane   +4 more
wiley   +1 more source

Aerosol Jet Printing of Benzocyclobutene as a Thermally Stable, Low‐Loss Dielectric for Multilayer Microwave Electronics

open access: yesAdvanced Materials Technologies, EarlyView.
Multilayer aerosol jet printed components with a low‐loss, thermally stable dielectric are demonstrated using benzocyclobutene. Ink formulation and in‐line droplet evaporation control support high‐quality, versatile, and stable printing performance. A specialized measurement for low‐loss materials reveals promising microwave properties, which, combined
Md Ramjan Ali   +3 more
wiley   +1 more source

Photoluminescence Reshaping via Structural Confinement and Local Density of Optical States Control in Ir(III)‐Doped Biodegradable Metasurfaces

open access: yesAdvanced Materials Technologies, EarlyView.
Phosphorescent biodegradable metasurface showing vibronic selection and spectral photoluminescence narrowing. Anti‐correlation between experimental LDOS and measured lifetimes. ABSTRACT Metasurfaces incorporating phosphorescent emitters offer a route to engineer radiative and vibronic processes beyond chemical design.
Vincenzo Caligiuri   +11 more
wiley   +1 more source

Characterized Ecoflex Polydimethylsiloxane (PDMS) Hybrids for Advanced Flexible Devices

open access: yesAdvanced Materials Technologies, EarlyView.
Ecoflex–PDMS hybrids are systematically characterized to identify an optimal composition that balances stretchability, optical transparency, and plasma bonding, enabling multifunctional applications in stretchable microfluidics, flexible sensing, and soft robotics.
Xiaoyue Kang   +10 more
wiley   +1 more source

Home - About - Disclaimer - Privacy