Results 251 to 260 of about 4,305,036 (352)

Multi-Morphology CeO₂ Synthesis via Synergistic Induction by Solvent and Ammonium Bicarbonate. [PDF]

Molecules
Xu Y, Hu Y, Li S, Gong X, Xiao S, Zhang X, Li L, Liu Y, Ding Z.   +8 more
europepmc   +1 more source

On the Importance of Subword Information for Morphological Tasks in Truly Low-Resource Languages

, 2019
Yi Zhu, Benjamin Heinzerling, Ivan Vulić, Michael Strube, Roi Reichart, Anna Korhonen   +5 more
openalex   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

Advanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter, Thomas Wegener, Andreas Schilling, Martin Fehlbier, Thomas Niendorf   +4 more
wiley   +1 more source

Shouldering the challenge of deciphering avian palate evolution. [PDF]

Proc Natl Acad Sci U S A
Benito J, Kuo PC, Torres CR, Navalón G, Plateau O, Clark AD, Steell EM, Field DJ.   +7 more
europepmc   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

Advanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud, Jakob Gruber, Hakan Göçerler, Pierluigi Bilotto, Christian Gierl‐Mayer, Elham Loni, Michael Naguib, Carsten Gachot   +7 more
wiley   +1 more source

Influence of Intra-Articular Tunnel Aperture Morphology on Clinical Outcomes and Graft Rerupture After ACL Reconstruction. [PDF]

J Clin Med
Iyetin Y, Koraman E, Akan M, Turkmen I, Akyurek M.   +4 more
europepmc   +1 more source

Design and Prototyping of Topology‐Optimized, Additively Manufactured Lightweight Components for Space Robotic Systems: A Case Study

Advanced Engineering Materials, EarlyView.
The results demonstrate a simulation‐driven workflow that applies LSB topology optimization with additive manufacturing constraints to mission‐specific load cases, integrating European Cooperation for Space Standardization compliant verification and manufacturability to develop structurally efficient rover suspension components.
Stelios K. Georgantzinos, Grigorios Kostopoulos, Eleni Papadopoulou, Stefanos Voulgaris, Alexandra Tseni, Panteleimon Bakalis, Maria N. Gkara, Chara Ch. Mitropoulou, Georgios Kazakis, Alin Munteanu, Jeremi Gancet, Nikos D. Lagaros   +11 more
wiley   +1 more source

Ejection Fraction-Related Differences in Left Ventricular and Atrial Strain Indices Among Pediatric Fontan Circulation with Systemic Left Ventricle Morphology. [PDF]

Diagnostics (Basel)
Șuteu CC, Fagarasan A, Suteu N, Cerghit-Paler A, Gozar L, Mărginean CO, Săsăran MO, Iancu M.   +7 more
europepmc   +1 more source

Mechanically Deposited Wear‐Resistant Amorphous Zr55Cu30Al10Ni5 Coatings

Advanced Engineering Materials, EarlyView.
Mechanically deposited from glassy ribbons, the Zr55Cu30Al10Ni5 amorphous coating formed a hard, continuous layer on AISI 1010 steel, tripling substrate hardness, lowering friction, and reducing wear. Despite its rough surface, it showed friction and wear behavior comparable to the crystalline alloy, highlighting its strong potential as a durable ...
Tales Ferreira, Pietro Cazelatto Bortolini, André Luiz Vidilli, Paulo Wilmar Barbosa Marques, Jéferson Aparecido Moreto, Claudio Shyinti Kiminami, Walter José Botta, Claudemiro Bolfarini, Guilherme Yuuki Koga   +8 more
wiley   +1 more source