Results 181 to 190 of about 801,068 (288)

A return to normality: A descriptive qualitative interview study exploring the patient experience of gout flare resolution

Arthritis Care &Research, Accepted Article.
Objectives While the definition of a gout flare is well established, the state of gout flare resolution has not yet been defined. This study aimed to explore patients’ experiences and perceptions of gout flare resolution. Methods Semi‐structured interviews were conducted with 24 people with gout, guided by open‐ended questions exploring their ...
Sarah Stewart, Anne Horne, Angelo Gaffo, Lisa K Stamp, N Lawrence Edwards, Nicola Dalbeth   +5 more
wiley   +1 more source

WS-SfMLearner: self-supervised monocular depth and ego-motion estimation on surgical videos with unknown camera parameters. [PDF]

J Med Imaging (Bellingham)
Lou A, Noble J.
europepmc   +1 more source

Low-energy motion estimation memory system with dynamic management. [PDF]

J Real Time Image Process, 2021
Silveira DS, Amaral L, Povala G, Zatt B, Agostini LV, Porto MS, Bampi S.   +6 more
europepmc   +1 more source

Thermoreflectance Detection of Point Defects Resulting from Focused Ion Beam Milling

Advanced Engineering Materials, EarlyView.
Focused ion beam (FIB) milling is a common tool for nanoscale material processing, however irradiation damage, redeposition, and contamination can occur. We use several characterization tools to show FIB‐induced effects beyond 1 mm from the milled area.
Thomas W. Pfeifer, Eric R. Hoglund, Anton V. Ievlev, Patrick E. Hopkins   +3 more
wiley   +1 more source

In vivo Multi-perspective 3D + t Ultrasound Imaging and Motion Estimation of Abdominal Aortic Aneurysms. [PDF]

Ultrason Imaging
Maas EJ, Donkers KM, de Hoop H, Nievergeld AHM, Thirugnanasambandam M, van Sambeek MRHM, Lopata RGP.   +6 more
europepmc   +1 more source

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Investigation of Motor Learning Effects Using a Hybrid Rehabilitation System Based on Motion Estimation. [PDF]

Sensors (Basel)
Takenaka K, Shima K, Shimatani K.
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Quantitative Analysis of Small Intestinal Motility in 3D Cine-MRI Using Centerline-Aware Motion Estimation. [PDF]

J Magn Reson Imaging
van Harten LD, de Jonge CS, Struik F, Stoker J, Išgum I.   +4 more
europepmc   +1 more source

Innovative Processing of Compacted Waste Aluminum Alloy Powders via Controlled Remelting and Solidification

Advanced Engineering Materials, EarlyView.
This study demonstrates an efficient recycling route for out‐of‐spec AlSi10Mg atomized powders through compaction and arc remelting followed by suction casting. By correlating compaction load, cooling rate, and resulting microstructure, we show that intermediate pressures (50–80 kN) and rapid cooling refine dendrites, reduce porosity, and enhance ...
Mila Christy de Oliveira, Marcella Gaute Cavalcante Xavier, Abdoul‐Aziz Bogno, Piter Gargarella, José Eduardo Spinelli   +4 more
wiley   +1 more source